Search

Type: Posts; User: HiPeRcO

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    1
    Views
    30

    LR503, it's in the electrical box in an 01.

    LR503, it's in the electrical box in an 01.
  2. Replies
    9
    Views
    142

    No water in the exhaust, obviously.

    No water in the exhaust, obviously.
  3. Replies
    9
    Views
    142

    In absence of something like a backfire that...

    In absence of something like a backfire that damages them, the resonators are generally quite reliable, they do a fine job diminishing the exhaust note, and do not impair performance in the least. ...
  4. Replies
    9
    Views
    142

    It will only increase noise and annoy your...

    It will only increase noise and annoy your neighborhood. Don't do it. :facepalm:
  5. Replies
    32
    Views
    1,156

    Interesting, do you have a link to the pump you...

    Interesting, do you have a link to the pump you bought?
  6. Replies
    12
    Views
    198

    Your next step is to measure open circuit AC...

    Your next step is to measure open circuit AC volts on all 5 stator winding pairs while cranking.
  7. Replies
    11
    Views
    235

    No worries, we just want to be able to help. ...

    No worries, we just want to be able to help. Having all the same project info in the same thread helps a lot 8-)
  8. Replies
    11
    Views
    235

    I'ts best to keep your posts in your original...

    I'ts best to keep your posts in your original thread.

    Now, what are you showing there? :)
  9. Yes, see this link:...

    Yes, see this link: http://greenhulk.net/forums/showthread.php?t=193070&page=8&p=2952472&viewfull=1#post2952472
  10. Replies
    11
    Views
    235

    By the way, it would be great if you can update...

    By the way, it would be great if you can update your profile to include your location. Perhaps there is a Weber guru nearby that can offer advice and/or assistance.
  11. Replies
    11
    Views
    235

    K447's excellent knowledge pages...

    K447's excellent knowledge pages are a great place to begin.
  12. Replies
    11
    Views
    235

    Welcome to Greenhulk! That is a good ski when...

    Welcome to Greenhulk!

    That is a good ski when sorted out but you've got a lot of work ahead of you.

    May I kindly suggest that you spend a few hours here in the MSX forum. Then come back with...
  13. Check head and injector for damage. If nothing...

    Check head and injector for damage. If nothing obvious then rebuilding the injector with new orings is probably in order.
  14. Replies
    12
    Views
    198

    Most likely you have low injector volts, either...

    Most likely you have low injector volts, either due to a flywheel/stator issue, or an EMM problem. Check the voltage on the white/red wire while cranking (should be around 20vdc). Then if low ...
  15. Replies
    20
    Views
    354

    No cranking suggests a missing wire, or bad...

    No cranking suggests a missing wire, or bad connection somewhere.

    FYI the MSX140 does not have a start/stop module, not sure if you were referring to the switches themselves though (which of...
  16. Replies
    1
    Views
    83

    Check this link here:....

    Check this link here:. http://greenhulk.net/forums/showthread.php?t=275073
  17. Replies
    25
    Views
    508

    If your pump is drawing less than 4 amps, ride...

    If your pump is drawing less than 4 amps, ride it! 8-)
  18. Replies
    25
    Views
    508

    There is very little risk in burning out the fuel...

    There is very little risk in burning out the fuel pump driver, as it has built in current limit and thermal protection. The pin on the EMM probably can't withstand more than 5A or so (I should look...
  19. Replies
    25
    Views
    508

    Leave the wiring alone. No reason at all to mess...

    Leave the wiring alone. No reason at all to mess with it.
  20. Replies
    25
    Views
    508

    Nope, poor quality control. Unfortunately they...

    Nope, poor quality control. Unfortunately they are the only game in town from an "higher but hopefully still acceptable" current draw vs OEM.
  21. Replies
    2
    Views
    115

    I am thinking battery vent tube

    I am thinking battery vent tube
  22. Replies
    25
    Views
    508

    Not hard at all to get an acceptable aftermarket...

    Not hard at all to get an acceptable aftermarket pump (sub 4 amp draw). This has been documented and tested for quite some time now. As far as taking the load off the EMM, where do you think the...
  23. Replies
    9
    Views
    239

    Welcome to Greenhulk! First things first, is...

    Welcome to Greenhulk! First things first, is this a carbureted model or direct injection?
  24. Glad to hear it, thanks!

    Glad to hear it, thanks!
  25. Replies
    3
    Views
    129

    59-60 mph stock 150, 63-65 mph with the PS tune

    59-60 mph stock 150, 63-65 mph with the PS tune
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4