Search

Type: Posts; User: ShortbusDevil

Search: Search took 0.02 seconds.

  1. Replies
    22
    Views
    1,422

    On my old 2000 GTX I set the manual lever to...

    On my old 2000 GTX I set the manual lever to neutral, and switch between for-neu-rev to hold position if there is any current where im at. If I am working a point or structure for a while I will just...
  2. Replies
    24
    Views
    1,848

    Vband clamp threads stripped, new gaskets and...

    Vband clamp threads stripped, new gaskets and clamp in with no leaks I can see. Dropping in the water in the morning when I get off in the morning.
  3. 1. I'm getting my gauges replaced as well. Makes...

    1. I'm getting my gauges replaced as well. Makes no sense (IMHO) to completely restore a ski and leave dead gauges on it. (You can pull the float and check with OHM meter, there is a baffle repair...
  4. Replies
    24
    Views
    1,848

    http://www.sea-doo.net/techarticles/techarticles.a...

    http://www.sea-doo.net/techarticles/techarticles.asp?page=april

    Should be the one. Bad-Link
  5. Replies
    24
    Views
    1,848

    I ordered the exhaust kit from SBT with the...

    I ordered the exhaust kit from SBT with the rubber diaper boot, new bolts. I'll search for the write up as well.
    Hopefully back in the water Sunday, depends on the parts arriving.
  6. No update? Nmpeter, didn't the Sugar Sand line...

    No update?

    Nmpeter, didn't the Sugar Sand line of jet boats and Polaris EX series use the same drive system? Almost bought one back in the day, friend warned me not to. "Just get another Bass Boat"
  7. Replies
    24
    Views
    1,848

    Update: New steering cable installed. New...

    Update:
    New steering cable installed.
    New (used) nozzle with correct reverse gate located and installed. (Factory correct, no rigging the VTS anymore)
    New Coils, starter relay (solenoid) in rear...
  8. Replies
    24
    Views
    1,848

    Everything went well, except my steering cable...

    Everything went well, except my steering cable snapped. (Not at speed) My speedometer is still broken, haven't checked top speed with my gps app. It's been a really crappy winter in Houston, with the...
  9. Replies
    24
    Views
    1,848

    Quick update: Both tanks (oil/gas) have been...

    Quick update:

    Both tanks (oil/gas) have been removed and cleaned.
    All fuel lines replaced, shut-off valve replaced.
    Seat re-covered (took two stabs at it myself but looked horrible) Baytown...
  10. Replies
    24
    Views
    1,848

    Finally got the motor to break free, other than...

    Finally got the motor to break free, other than the counter-balancer...its a complete rebuild.( I had assumed as much from the start.) Jet pump is rebuilt with new bearings and wear ring/ impeller....
  11. Replies
    24
    Views
    1,848

    Will do....and Thanks I'll throw you a PM if I...

    Will do....and Thanks I'll throw you a PM if I do...down mostly to electronics now..I think I have everything fairly sorted out.
  12. Replies
    24
    Views
    1,848

    No racing in its future...trying to build it back...

    No racing in its future...trying to build it back to stock (Less oversize bores, bumping up jets). Just going to be a cruiser. I've read that thread 6 times or so, you have a machine shop at your...
  13. Replies
    24
    Views
    1,848

    My old impeller is above, Solas is an upgrade....

    My old impeller is above, Solas is an upgrade. This ski is just for me to tool around on, mount the cooler/rod holder rack on and fish Lake Houston and East Bay with. (Although we have Alligators in...
  14. Replies
    24
    Views
    1,848

    Update: New parts came in, impeller, tool,...

    Update:

    New parts came in, impeller, tool, wear ring. Ordered an ebay nozzle (mine was damaged) the one I got also has VTS adjustment (Will have to make a stand-off and turnbuckle to adjust it...
  15. Replies
    24
    Views
    1,848

    I got the 15/20 because it was the closest I...

    I got the 15/20 because it was the closest I could find to stock pitch, mine is not worthy of re-surfacing.http://www.greenhulk.net/forums/attachment.php?attachmentid=435879&stc=1
    Image from...
  16. Replies
    24
    Views
    1,848

    Resurrecting a 2000 GTX 951 3 seater

    New to the forums, just bought my first project ski.

    Background:

    I've always done my own repairs/maintenance on my vehicles/toys. Found a decent project ski locally and figured why not. (Famous...
Results 1 to 16 of 16