Search

Page 1 of 14 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    9
    Views
    141

    http://greenhulk.net/forums/showthread.php?t=19994...

    http://greenhulk.net/forums/showthread.php?t=199941&p=2194716&viewfull=1#post2194716



    http://greenhulk.net/forums/showthread.php?t=58457&p=648170&viewfull=1#post648170
    ...
  2. Replies
    9
    Views
    141

    http://greenhulk.net/forums/showthread.php?t=27126...

    http://greenhulk.net/forums/showthread.php?t=271267&p=2949695&viewfull=1#post2949695

    http://greenhulk.net/forums/showthread.php?t=266098&p=2897199&viewfull=1#post2897199
    ...
  3. Replies
    25
    Views
    508

    What might be the difference in voltage loss...

    What might be the difference in voltage loss between the OEM fused power feed wire harness wiring and a separate/dedicated fused wire feeding the fuel pump load?

    Is that voltage difference enough...
  4. Replies
    25
    Views
    508

    That is not how basic 12 volt systems work, in a...

    That is not how basic 12 volt systems work, in a car or watercraft.

    The battery provides a stabilizing effect while the charging system holds the ‘12 volt’ voltage above the battery’s natural...
  5. The Ficht EMM is a computer controlled system....

    The Ficht EMM is a computer controlled system. The computer decides to stop the engine, and therefore stops firing the fuel injectors and the ignition coils.

    The Ficht ignition coils do not have...
  6. Replies
    3
    Views
    163

    Click here, start reading :) ...

    Click here, start reading :)


    http://polarispwcknowledge.shorturl.com/first-things-to-do
  7. Replies
    0
    Views
    208

    Sticky: Asking for help via Private Message

    I often receive Private Messages via GreenHulk asking for assistance with someone’s watercraft.

    While it is my inclination to help, I prefer that people create a new thread and post their...
  8. Replies
    15
    Views
    406

    Howdy. Spencer's build (link above) is the only...

    Howdy.
    Spencer's build (link above) is the only one I know of that actually did it. I too have a nice FST block that I plan to use, if I ever get around to it.

    You will need the special...
  9. Replies
    6
    Views
    204

    To check on the turbo... you have to get your...

    To check on the turbo... you have to get your fingers in the compressor inlet opening. To do that, you have to first unbolt (2 bolts) the intercooler (IC) and loosen/remove the 2 intake hoses to the...
  10. 04 Genisis i is back running thanks to Darrin at...

    04 Genisis i is back running thanks to Darrin at Lakeside Tech! In the beginning when this machine quit I replaced the stator thinking that was my problem, that didn't fix it. I sent the EMM off for...
  11. Replies
    16
    Views
    249

    Just to make sure we're singing from the same...

    Just to make sure we're singing from the same sheet of music, you had your meter set for DC volts when measuring at the white/red wire?

    Yes, your issue could be in the EMM or it could be the...
  12. Replies
    5
    Views
    165

    Lakeside Tech just repaired another one for me....

    Lakeside Tech just repaired another one for me. Put it back in the ski and it fired right up!!
  13. Replies
    9
    Views
    364

    Update your profile to indicate your location. ...

    Update your profile to indicate your location. There maybe someone nearby with an alignment tool. Here as an aftermarket alternate and this is what I utilize:

    1) This rod: ...
  14. Replies
    15
    Views
    284

    Good enough. HiPeRcO will take good care of you.

    Good enough. HiPeRcO will take good care of you.
  15. When the LR-503 module is bypassed; it is not...

    When the LR-503 module is bypassed;
    it is not sensing anything.
    The red button cranks the starter. Even if engine is already running.
    And the lanyard pull is supposed to shut the engine off, by...
  16. Replies
    9
    Views
    312

    I was somewhat surprised by the amount of...

    I was somewhat surprised by the amount of contaminants that made it past the filter on the bottom of the canister assembly. Carter (the source vendor for the canister) does not refer to it as a...
  17. Replies
    12
    Views
    467

    This is a common repair. The through hull...

    This is a common repair. The through hull driveshaft seal assembly is a wear item and eventually needs to be rebuilt.

    Click my signature link, then look in the jet pump section for details on the...
  18. Replies
    5
    Views
    180

    sometimes some lube can do the trick, but who...

    sometimes some lube can do the trick, but who wants to take that chance getting stuck on the water when it rears it's uncooperative head once again. replacements are inexpensive enough.

    pull it...
  19. Replies
    2
    Views
    204

    Welcome to GH! So it is properly running on 2...

    Welcome to GH!

    So it is properly running on 2 cylinders now... all the time?

    Unbolt the intercooler and remove the big intake hoses (not the 2 water lines on the right side). Slide the...
  20. Cheers!

    Cheers!
  21. Welcome to MSX150 life! Kudoes to you for...

    Welcome to MSX150 life!

    Kudoes to you for reading up on the unique Weber-engined ski and learning it's eccentricities... like proper oil level, preventing oil ingestion (catch can), etc.

    Milky...
  22. Replies
    28
    Views
    1,063

    LOL>.kind words are that you can tell a good joke...

    LOL>.kind words are that you can tell a good joke and your wife isn't "that bad looking" :-)

    fact of the matter is you demonstrated the kind of expertise that gets my endorsement!

    and you know...
  23. Replies
    2
    Views
    184

    Look carefully inside the hollow of the drive...

    Look carefully inside the hollow of the drive coupler. Sometimes the rubber bumper falls off in there.

    Inspection mirror and a light. Or a camera.
    ...
  24. Replies
    6
    Views
    501

    Welcome to the Hulk. Where in OH are you...

    Welcome to the Hulk.

    Where in OH are you located?

    Just a FYI for you:

    650cc = 68HP and around 45 MPH

    750cc = 80HP and around 48 MPH
  25. Thread: Hi everyone again

    by K447
    Replies
    6
    Views
    239

    The correct fix for the fuel pressure regulator...

    The correct fix for the fuel pressure regulator requires it to be reinforced. Just pushing it back into the plastic hole is not enough.
Results 1 to 25 of 328
Page 1 of 14 1 2 3 4