Search

Type: Posts; User: casey67

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    20
    Views
    5,089

    Welcome to GreenHulk. It would probably be...

    Welcome to GreenHulk.

    It would probably be best to start your own thread with a WTB.
    Post pictures of the seats and damage you have.

    The 98 was a one year only 2 piece design. All other models...
  2. The SLT had the choke lever on the handle bar...

    The SLT had the choke lever on the handle bar switch-so NO, it will not work on a Virage.
    This is the official parts site to look stuff up.; http://parts.polarisind.com/Assemblies.asp
  3. Replies
    2
    Views
    38

    Welcome to GreenHulk. Yes it can be tested on...

    Welcome to GreenHulk.

    Yes it can be tested on the bench. The piece that triggers the sensors it the magnet that is pressed into the black plastic ring at the center of the flywheel. That ring is...
  4. Replies
    1
    Views
    50

    John at Watcon.com / Rock county Jetski

    John at Watcon.com / Rock county Jetski
  5. Replies
    9
    Views
    170

    What makes you think it "seems to stop flowing" ?...

    What makes you think it "seems to stop flowing" ?
    Some models had a thermostat and bypass valve installed on the end of the water bar/manifold. See if that has those parts and if stuck. By the way...
  6. Replies
    29
    Views
    806

    Honestly I don't know what the Gen2 is. IIRC it...

    Honestly I don't know what the Gen2 is. IIRC it was a change in CDI.
    As far as I know/all I have ever worked with, there are only 2 versions. Old style is old style and only works with Gen1 stuff.
    ...
  7. Thread: Won't restart

    by casey67
    Replies
    1
    Views
    91

    Does the choke help with starting ? Post a...

    Does the choke help with starting ?
    Post a picture of the carbs. Is the idle set ?
  8. Welcome to GreenHulk. The 97 gas tank will not...

    Welcome to GreenHulk.
    The 97 gas tank will not come out the front. Need to remove the engine.

    If the gas left the stain and trash, I would bet Gas should desolve/clean it.
    Probably need to find...
  9. heystretch ! Welcome to GreenHulk. It would...

    heystretch ! Welcome to GreenHulk.

    It would probably still make sense to make sure the cylinders are equal in temperature after running.
    But from your description, More likely not misfire....
  10. Replies
    29
    Views
    806

    the 2873022 # is for THE update kit- stator CDI...

    the 2873022 # is for THE update kit- stator CDI and 2 cyl coil w/plug wires. Update is GEN3 stator and CDI.Everything needs to be replaced together/only works with Gen3 components. Stator should have...
  11. Good to hear. What exactly did you find in the...

    Good to hear.
    What exactly did you find in the carbs ?

    I'm still wondering about impeller pitch.
  12. Yes blk/yel is from the STOP switch. When...

    Yes blk/yel is from the STOP switch. When grounded by switch, it shuts off CDI entirely. Once it is disconnected at CDI-stop switch will not cause no start.

    Need to get mag piston to top dead...
  13. It stopped running because it lost spark. Now it...

    It stopped running because it lost spark. Now it has spark , but still does not run ?
  14. Replies
    13
    Views
    129

    I tested crankcase pressure on a 700 2 cyl. And...

    I tested crankcase pressure on a 700 2 cyl. And had 4-5 psi and 4-5 inhg suction. If I remember correctly.

    You will need spark plugs installed. Crankcase is open to combustion chamber depending on...
  15. Try to be more specific. It does not have...

    Try to be more specific.
    It does not have "vacuum hoses". Only fuel hoses. If pressure builds up in the gas tank-that pressure will push fuel out of the supply fuel hose UNTIL all pressure it...
  16. Replies
    27
    Views
    716

    Take the battery back to where you bought it, ask...

    Take the battery back to where you bought it, ask them to test it.
    Ask them for the actual cold cranking amps and voltage from the test.
  17. We heard of a couple popping out of the...

    We heard of a couple popping out of the aftermarket "roller bearing" thru hull seal.
    And that was caused by grease pushing it out.

    There isn't a "genuine" Polaris made seal. The seals have an...
  18. Replies
    31
    Views
    700

    Trim location will not affect running/starting. ...

    Trim location will not affect running/starting.

    There are 2 grey wires, the one with flat blade connector is for "limiter" or "warning" circuit. IT was originally a tan wire- there are a couple...
  19. Replies
    31
    Views
    700

    Is the idle about 1200 in the water ? Might as...

    Is the idle about 1200 in the water ?
    Might as well do the TSB jumper to take that out of diagnosis.

    My friends 96 sometimes has issues with the stop/start switch-he took it apart and found...
  20. Replies
    4
    Views
    79

    Same diagram as Polaris industries. And you...

    Same diagram as Polaris industries.
    And you found, identified the fuel sender tube marked "ON" for the fuel supply ?

    The center carb fitting for pulse hose has to be hooked up for fuel pump to...
  21. Replies
    29
    Views
    806

    This add shows the mounting holes nicely....

    This add shows the mounting holes nicely....
  22. Replies
    29
    Views
    806

    The cross head screws (phillips) hold the coils...

    The cross head screws (phillips) hold the coils to the mounting plate-wires will also be in there also.
    The plate mounting screws are what need to be removed. At some point Polaris switched from...
  23. Replies
    4
    Views
    79

    Welcome to GreenHulk. Are the hoses connected...

    Welcome to GreenHulk.

    Are the hoses connected as this diagram shows. http://parts.polarisind.com/Assemblies.asp

    Click on/choose "fuel system"
  24. The silicone seal is really tough as 1 piece.I...

    The silicone seal is really tough as 1 piece.I swear the hull will give way before the seal. I find that attacking one area with a scraper between the base and hull gets it to separate and remaining...
  25. When you had the jet pump off, was the o-ring on...

    When you had the jet pump off, was the o-ring on the cooling tube in good shape ?
    There is a small screen on the inside of exit nozzle,just opposite where the tube housing attaches to nozzle. Is...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4