Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    10
    Views
    218

    Typically I try to avoid "permanent" block mods...

    Typically I try to avoid "permanent" block mods but that is basically what I was thinging about doing.

    Yep, insead of water to coolant its water to oil.

    Sean
  2. Doo powered STX-R and STX-15f Builds

    Starting this as a premptive strike and planning thread. I snagged this pair of neglected and nasty salt water skis (2008 rxtx and gtx) about a year ago and am finally getting around to doing...
  3. On the kawasaki skis, if the gauge is faulty but...

    On the kawasaki skis, if the gauge is faulty but connected they will still run. They run in slo mode but the engine runs. With the gauge disconnected they do not have power to the ecu at all.
    ...
  4. Replies
    1
    Views
    82

    WTB - Parts I should have one. Let me see if I can find it. ...

    I should have one. Let me see if I can find it.

    Sean
  5. That is manageable for now. Are there any...

    That is manageable for now. Are there any aftermarket gauge options? Used oem seems to be 450ish and new is between 500 and 700.

    Sean
  6. Sticky: I will give that a try. I think I still have a...

    I will give that a try. I think I still have a few crusty pumps with swelled wear rings around.

    Sean
  7. Sticky: As in you cut the housing as well or you cut with...

    As in you cut the housing as well or you cut with the blade parallel to the pump shaft?

    Sean
  8. Sticky: What is your trick to remove the stock wear...

    What is your trick to remove the stock wear rings? I always figured it would be a pain to cut them out since the rear is so close to the stator vanes?

    Sean
  9. Is it possible to run ski without gauge cluster hooked up? (2008 RXT-X)

    Ignoring the obvious issue of "how are you supposed to know if you are about to explode, run out of gas, or sink" Is the gauge cluster required to run?

    On the Kawasaki STX skis if you disconnect...
  10. Replies
    5
    Views
    163

    I will find out if that is the case on the pair I...

    I will find out if that is the case on the pair I just brought home. Humidity and salt are a nasty combination. I am not hopeful.

    Sean
  11. Replies
    10
    Views
    218

    More or less, just not $500 worth of plates. ...

    More or less, just not $500 worth of plates.

    I picked up some version of an exchanger from


    http://www.dudadiesel.com/heat_exchangers.php

    For the water side so I may snag another for the...
  12. Replies
    10
    Views
    218

    Planning to stay closed loop with a parallel...

    Planning to stay closed loop with a parallel plate exchanger when I swap over to the stx hulls. I am also planning to keep some form of oil cooler on the ski wether block mounted as stock or remote....
  13. Replies
    10
    Views
    218

    I ride in the Houston area so water temps can get...

    I ride in the Houston area so water temps can get to 90+ f

    Sean
  14. New AEM 320lph fuel pumps, new NGK plugs, new OEM...

    New AEM 320lph fuel pumps, new NGK plugs, new OEM oil pressure switches, ARP flywheel bolts ordered.

    Going to keep cleaning these nasty skis up.

    Sean
  15. Currently planning to give it all a good clean...

    Currently planning to give it all a good clean this afternoon and check it over once I get the grot and bugs out. I need to see if I can snag the scan tool from a buddy of mine.

    Supposedly they...
  16. A little crusty but not as bad as I had feared....

    A little crusty but not as bad as I had feared. Remember kids, fluid film is your friend. Bonus frog from the gtx, Dog approves of the new shady spot under the js550, also a project.

    So far I...
  17. Replies
    10
    Views
    218

    2008 4-Tec External Oil Cooler

    I am in the planning phase of trying to stuff a 2008 RXT-X 255 into a Kawasaki STX hull without drastically cutting up the inner hull like the conversion guys typically do. This led me to the...
  18. Replies
    0
    Views
    45

    2008 4-Tec External Dimensions

    What are the approximate dims of an 08 4 tec with the intake and exhaust off? I did some digging the other night and couldn't find a good answer.

    Thanks,

    Sean
  19. Great, I will add it to the list. Thanks Pete. ...

    Great, I will add it to the list. Thanks Pete.

    I picked up a stainless parallel plate exchanger for when I swap the motors over so if I break the nipple off I may just swap that over rather than...
  20. So these followed me home... 08 GTX and 08 RXTX

    Long story short I ended up with an 08 GTX and RXTX, they lived a rough life before I aquired them with lots of neglect and salt. To make matters worse, I left them uncovered for a year... In Texas. ...
  21. Replies
    8
    Views
    144

    That turned out excellently Steve, I am seriously...

    That turned out excellently Steve, I am seriously impressed and will be replicating it.

    Sean
  22. The ultra used a different timing curve and fuel...

    The ultra used a different timing curve and fuel setup on each cylinder, if you have an issue on either of those it can cause meltdown. Check the electrical stuff as a cya.

    Sean
  23. That happened from time to time, as long as you...

    That happened from time to time, as long as you get all the gunk out and check the core for leaks it will pick back up.

    Sea.
  24. Basically anything that worked on a 15f will work...

    Basically anything that worked on a 15f will work on a sxr. The problem comes down to tuning and who/how its done.

    Cams from a zx12r fit but you need a tune.
    Intake mods work but you need to...
  25. With how thin the pipe is, it would probably seat...

    With how thin the pipe is, it would probably seat as long as its tightened even if its not flat just from bending.

    The problem/benefit of using 3 separate cylinders is that you don't need to be...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4