Search

Type: Posts; User: hyoctane23

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    3
    Views
    344

    FS Do you have any pics you could post?

    Do you have any pics you could post?
  2. Replies
    9
    Views
    346

    That is correct! I sprayed quite a bit of the...

    That is correct! I sprayed quite a bit of the cable lube in the bag so that gravity could work its magic. The tape of course was to seal the hole so it didn't completely leak everywhere...buuuuut be...
  3. Replies
    9
    Views
    346

    Here is a picture of how you can free up the...

    Here is a picture of how you can free up the cable using spray cable lube from any auto parts store. I do this for all my cables and it works very well.
  4. Replies
    86
    Views
    3,790

    Have you read the whole thread lol. Already a...

    Have you read the whole thread lol. Already a couple of suggestions [emoji102][emoji102][emoji102]
  5. Replies
    86
    Views
    3,790

    Your clearance sounds about right. If the...

    Your clearance sounds about right. If the cylinders looked like that before you got into it, the engine probably wasn't warmed up enough before dropping the hammer or was ridden in very cold water. ...
  6. Replies
    86
    Views
    3,790

    x2 from the guys comments above. I have WSM 750...

    x2 from the guys comments above. I have WSM 750 pistons in my limited boat and they have run well, even at 8000+ rpm. I did have an issue with a piece of skirt breaking off but it luckily went...
  7. Replies
    86
    Views
    3,790

    so very true!!!!!!

    so very true!!!!!!
  8. Replies
    86
    Views
    3,790

    I literally spent hours and hours and hours on my...

    I literally spent hours and hours and hours on my super stock 785 getting all the gaskets to match all the ports without any overhang, polishing the exhaust duct and matching the exhaust flange ID...
  9. Replies
    48
    Views
    1,047

    Could you post a picture of how this is routed in...

    Could you post a picture of how this is routed in your boat?
  10. Replies
    48
    Views
    1,047

    Head pipes and the actual pipes are aluminum. Do...

    Head pipes and the actual pipes are aluminum. Do NOT use muriatic acid to clean those. I had a head pipe clog up before and I tried vinegar as well but had no luck. I had to get a new head pipe...
  11. FS - Parts Damn, what old ass computer can even run that...

    Damn, what old ass computer can even run that program anymore? [emoji1787][emoji1787]
  12. Replies
    48
    Views
    1,047

    What springs and seats were you testing?

    What springs and seats were you testing?
  13. Replies
    48
    Views
    1,047

    I meant the picture of the spring that sdlvx...

    I meant the picture of the spring that sdlvx posted, not the chart. The chart you posted is good except the 115 gram springs are no longer gold but shiny silver.
  14. Replies
    48
    Views
    1,047

    What do you mean by "free rev?"

    What do you mean by "free rev?"
  15. Replies
    48
    Views
    1,047

    They all should be the same spring and N/S. I...

    They all should be the same spring and N/S. I believe the Pro uses 65 gram springs stock. I know that one chart shows 80 gram springs but they probably did that in an effort to stop the carb from...
  16. Replies
    48
    Views
    1,047

    The picture of the spring you posted does NOT...

    The picture of the spring you posted does NOT look like a proper Mikuni spring.
  17. Replies
    13
    Views
    1,603

    What RPM are you hitting in a straight line?

    What RPM are you hitting in a straight line?
  18. Replies
    5
    Views
    409

    You've basically found the two remaining piston...

    You've basically found the two remaining piston sources for our 785s...Wiseco or WSM. You'll probably never find another stock 785 piston unless someone has one laying around in their garage. I'd...
  19. Replies
    19
    Views
    586

    I'm not going to say that the fuel system valves...

    I'm not going to say that the fuel system valves are going to be 100% critical on your system but I know for sure they help a lot.

    Were you able to do any testing after clipping the wires?
  20. Replies
    19
    Views
    586

    I'd say check the vent/check valves and clip the...

    I'd say check the vent/check valves and clip the wires first and go from there.

    By using a regulator from an air compressor, you won't really know if they are leaking since the regulator will...
  21. Replies
    19
    Views
    586

    That really isn't the best way to check popoff. ...

    That really isn't the best way to check popoff. You'll never know if you have a leaky N&S valve or one that is so far out of spec.

    The tank has some pressure to help with fuel delivery. If...
  22. Replies
    19
    Views
    586

    For the popoff, what readings were you getting? ...

    For the popoff, what readings were you getting? I presumed you checked each carb individually and got 15-18 psi and it held the pressure after it popped?

    There are two small circular check valves...
  23. Replies
    19
    Views
    586

    There are so many things that can be causing a...

    There are so many things that can be causing a bog here. Off the top of my head...maybe others can chime in too:

    1. Have you checked compression?
    2. Did you check the popoff pressure with the...
  24. Replies
    19
    Views
    586

    Their position is RPM dependent but if they're...

    Their position is RPM dependent but if they're stuck open, you'll get a bog out of the hole. What full speed RPM are you getting now?
  25. Replies
    19
    Views
    586

    Have you checked the exhaust valves to be sure...

    Have you checked the exhaust valves to be sure they're moving when you rev the throttle?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4