Search

Type: Posts; User: badjoka

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Thanks, I'm going to incorporate some of your...

    Thanks, I'm going to incorporate some of your points here, better now then later on the water.
  2. As a winter project, im also going back to a semi...

    As a winter project, im also going back to a semi stock exhaust or completely stock with the Tommy Jordan mod. I was thinking of using the OEM waterbox and resonator tied into silicone hose to my...
  3. Replies
    1
    Views
    183

    I'm in Fairfield CT, just dropped off my ski...

    I'm in Fairfield CT, just dropped off my ski Saturday at Ryan's autobody in NJ. Always reasonably priced and excellent work. It's a trip for me, 2 hours, but the offset is the repair is done right...
  4. Not an expert, but did you double check each...

    Not an expert, but did you double check each electrical connection at the intake manifold side and as a baseline, I would check each fuse individually for continuity. Just getting the basics out if...
  5. Have a safe trip. CT jetski club on facebook,...

    Have a safe trip. CT jetski club on facebook, https://www.facebook.com/groups/166501253799577 is also trying to set up a ride to block island, this weekend I think.
  6. Replies
    2
    Views
    137

    Congrats! Where did you launch from?

    Congrats! Where did you launch from?
  7. Replies
    14
    Views
    3,149

    Thanks for the info TJ, Anyone ever try the...

    Thanks for the info TJ,

    Anyone ever try the state ramp in Westport, every time I pass over on the train it looks empty.
  8. Updating my post: I had issues with my build,...

    Updating my post: I had issues with my build, narrowed down to the 3 bar map sensor. Deans tune is set for the OEM map sensor, he makes the required adjustments in the fuel table.
  9. Replies
    15
    Views
    744

    I finally talked to Dean, been impossible to...

    I finally talked to Dean, been impossible to reach him but he called me, and most importantly he is ok, but the state covid regulations, season demand and the disease itself are impacting his shop...
  10. Replies
    15
    Views
    744

    I've been also been trying to contact Dean....

    I've been also been trying to contact Dean. Email, voicemail and FB message, all with no luck. Having problems with his tune, more specifically, may be setup for a 2 bar MAP not 3 bar which is what I...
  11. Replies
    6
    Views
    481

    I remember reading through this awhile ago. ...

    I remember reading through this awhile ago.

    http://greenhulk.net/forums/showthread.php?t=278088
  12. Replies
    6
    Views
    386

    Thanks! I'm hoping that when Dean see the ecu, he...

    Thanks! I'm hoping that when Dean see the ecu, he will confirm its set for 2 bar, not 3 bar. Being the dummy that I am, I totally forgot when swapped the R&D for Deans two years ago I had an...
  13. Replies
    6
    Views
    386

    Well, found the problem at last. Firstly, I...

    Well, found the problem at last.

    Firstly, I tried new spark plugs, installed the Riva throttle body, checked all clamps, changed map hose due to a kink in the line, cleaned out fuel system, and...
  14. Replies
    3
    Views
    470

    Yes, I bought one off ebay a few years and had no...

    Yes, I bought one off ebay a few years and had no problems. Haven't touched it in a long time but will be using soon, fingers crossed.
  15. Replies
    3
    Views
    306

    Not sure about the o-ring, but might as well...

    Not sure about the o-ring, but might as well rebuild the pump but read this first, very informative threads.

    http://greenhulk.net/forums/showthread.php?t=37951&page=2

    ...
  16. Replies
    6
    Views
    386

    Have the same issue with very erratic idle, the...

    Have the same issue with very erratic idle, the last few days working on it as time allows, will post my cause when I find it.
  17. Congrats on the ski! Good choice on the FX. A few...

    Congrats on the ski! Good choice on the FX. A few years ago I had my FZR on the GSB (Bayport area) and the chop just beats you up. FX flew by me without a care in the world.
  18. Replies
    56
    Views
    5,734

    I read that the 4000 is 1/2 the holding power of...

    I read that the 4000 is 1/2 the holding power of 4200. 4200 allows disassembly, 5200 is permanent. I used the 4200 in case I ever have to disassemble it. One thing to note, when I was at Western...
  19. Replies
    14
    Views
    3,069

    FS - Parts Bump for a great and honest seller!

    Bump for a great and honest seller!
  20. Just ordered one! Thanks Jerry. Xmas around the...

    Just ordered one! Thanks Jerry. Xmas around the corner.
  21. FS Here ya go, www.xtremekreations.com...

    Here ya go,

    www.xtremekreations.com

    http://greenhulk.net/forums/member.php?u=61055
  22. FS Just PM or email him at his website, Jim is...

    Just PM or email him at his website, Jim is quick to respond.
  23. Thread: Rideplate

    by badjoka
    Replies
    1
    Views
    486

    Just a light sand, make it smooth and paint....

    Just a light sand, make it smooth and paint. Plate is not the greatest, so don't worry about it. One of the very few items at Riva that are meh. Get jims plate when you can.
  24. Replies
    56
    Views
    5,734

    Good read: ...

    Good read:

    http://www.greenhulk.net/forums/showthread.php?t=117375
  25. Replies
    62
    Views
    5,312

    Just posting some info from my conversation with...

    Just posting some info from my conversation with Dean last month.

    I requested a tune for SHO and wanted static fuel pressure, I dont have the patience to mess with a regulator.

    Dean advised I...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4