Search

Type: Posts; User: HiPeRcO

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    5
    Views
    99

    Classic EMM problem. Send it to me (Lakeside...

    Classic EMM problem. Send it to me (Lakeside Tech) and I will fix it 8-)
  2. It's not likely due to fouled plugs. The DI...

    It's not likely due to fouled plugs. The DI ignition system is quite monstrous. Have you checked fuel pressure when it dies?
  3. Sticky: Awesome advice from the sage master. =D> It...

    Awesome advice from the sage master. =D>

    It is very true that MOST questions that can be asked, have been asked and answered MANY times by now :)

    (Now, where was that post again about the...
  4. Replies
    10
    Views
    169

    Failure to idle can be caused by incorrect spark...

    Failure to idle can be caused by incorrect spark plugs. NGK PZFR6H only! (No "equivalents" or "substitutes")
  5. Thread: Lr module

    by HiPeRcO
    Replies
    2
    Views
    67

    Minks was OEM, if that is your question?

    Minks was OEM, if that is your question?
  6. Replies
    112
    Views
    3,159

    Sounds like you are making progress, keep at it...

    Sounds like you are making progress, keep at it 8-)
  7. Replies
    4
    Views
    159

    I don't think that will work, as it is for the...

    I don't think that will work, as it is for the Polaris DI (2 stroke) machines.
  8. Replies
    11
    Views
    244

    I'm afraid to say that it's not looking good. ...

    I'm afraid to say that it's not looking good. The starter would not normally be engaged unless the bendix is wadded up. Best guess is either wadded up flywheel/stator, or seized crank.
  9. Replies
    24
    Views
    500

    Was the ski left floating in the water :smt119 ...

    Was the ski left floating in the water :smt119

    I suppose the cooling line to the flywheel cover might allow water to come in, if it was disconnected and low enough in the hull.
  10. Welcome. What does the display SAY when the red...

    Welcome. What does the display SAY when the red warning light is on?
  11. Replies
    2
    Views
    76

    MFI CODE RESET...

    MFI CODE RESET in case you want a fish ;)
  12. Replies
    5
    Views
    137

    They often leak around the sending unit neck, but...

    They often leak around the sending unit neck, but that doesn't empty the tank into the hull. If you are losing the entire contents of the tank, either the tank is cracked or the connection between...
  13. Replies
    2
    Views
    92

    Its a ball and a spring. It "opens" and lets...

    Its a ball and a spring. It "opens" and lets fuel flow when the pressure is around 25 psi. It needs to be in the return line.
  14. Replies
    12
    Views
    284

    Convert it to a DI, starts easy, every time 8-)

    Convert it to a DI, starts easy, every time 8-)
  15. Replies
    6
    Views
    139

    Nice score! (and darn you, I want one 8-) ) ...

    Nice score! (and darn you, I want one 8-) )

    As long as you put in the same TYPE of oil (regular vs. synthetic), its probably fine to mix it. But if it were me I'd use more of what's there before...
  16. Replies
    24
    Views
    500

    Yikes. Multiple issues there. The flywheel...

    Yikes. Multiple issues there. The flywheel housing should not be full of water, nor should it be full of magnet parts and other debris :(
  17. Sticky: Its not very likely that the EMM was damaged...

    Its not very likely that the EMM was damaged during the stator "incident".

    - Have you checked the voltage on the injectors while cranking?
    - Did you install an aftermarket stator? If so,...
  18. Replies
    6
    Views
    148

    Don't be sorry, we're here to help. (Oh, and...

    Don't be sorry, we're here to help. (Oh, and Welcome to Greenhulk! 8-) )
  19. Replies
    6
    Views
    148

    If its blue it has carbs. Otherwise its direct...

    If its blue it has carbs. Otherwise its direct injected. (The presence of fuel injectors on the top of the cylinder heads is also a dead giveaway 8-)

    Injector on head picture
  20. Replies
    2
    Views
    93

    Welcome to Greenhulk! Tell us about the issues...

    Welcome to Greenhulk!

    Tell us about the issues you're having with your ski, and what makes you suspect that the EMM is bad.
  21. Replies
    112
    Views
    3,159

    That is also where the main water feed enters the...

    That is also where the main water feed enters the hull from the jet pump (black plastic tube in the photos above, below the loose pump base bolt). Its possible that your water inlet tube is not...
  22. Replies
    3
    Views
    177

    There aren't any updates for the computer. For...

    There aren't any updates for the computer.

    For the ski, make sure the injector fuel lines are not rubbing on the injector brackets, and ideally the return lines are protected with wire loom.
  23. You won't have a good core to exchange if you...

    You won't have a good core to exchange if you throw a rod through the block...
  24. See attached photo and text for the MSX engine...

    See attached photo and text for the MSX engine speed sensor tests.

    ENGINE SPEED SENSOR
    (Sensor Gap: .8mm ± .5mm (.03″ ± .02″)


    (Resistance: Pins 1 & 2) 860Ω @68_F (20C)
    (AC voltage: Pins 1 &...
  25. Extracting the pin without the wire attached is...

    Extracting the pin without the wire attached is going to be extremely difficult. I agree with K447, just replace the entire harness.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4