Search

Type: Posts; User: BLASTER 1

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    20
    Views
    560

    Try using some lubricant like blast off and some...

    Try using some lubricant like blast off and some heat also tap lightly with a hammer turn to remove in small increments. Could be it’s not corroded together but the threads are jacked up from debri...
  2. Is one air in one out ? When engine is running...

    Is one air in one out ?

    When engine is running there both sucking air in
  3. Replies
    20
    Views
    560

    Just use silicone, it helps keep the bolts and...

    Just use silicone, it helps keep the bolts and the bracket from rusting together. Never had a intake, sponson or rideplate bolt come loose from using silicone
    Definitely donít use red loctite
    And...
  4. Replies
    31
    Views
    1,577

    Dam, your grate was on the verge of ripping out!...

    Dam, your grate was on the verge of ripping out! Good thing you weren’t more aggressive riding that day
  5. Roughly at the top of the exhaust manifold, did...

    Roughly at the top of the exhaust manifold, did this just after installing the CAI.
    At least 2-1/2 years no issues, problems or water
  6. I used the original hose then stepped it up to...

    I used the original hose then stepped it up to run 3/4 hose and then replaced the oil cooler outlet with a bilge fitting for the breather vent
    The oil cooler out was put above the bumper so I could...
  7. It’s because your going to fast!! Try 3m 4200...

    It’s because your going to fast!!
    Try 3m 4200 it’s what I used and it’s holding tight after 3 years
  8. Replies
    2
    Views
    97

    Don’t you just hate when things like that happen!...

    Don’t you just hate when things like that happen! I know I do
  9. The air intake will give you some performance but...

    The air intake will give you some performance but more so with additional Mods, the more you modify the greater it helps
    The breather kit will keep oil residue out of your intake tract. I actually...
  10. Replies
    31
    Views
    1,577

    youngDump, have you been able to take any...

    youngDump, have you been able to take any pictures, just curious how bad it looks
  11. Just use a quality sealant like 3m 4200 fill...

    Just use a quality sealant like 3m 4200 fill slightly higher than the grate and install same in the back. I filled it in and sealed just the front of the rideplate And it’s still doing good
    And yes...
  12. Replies
    31
    Views
    1,577

    I’m guessing your in the 79-80 mph range, so ya...

    I’m guessing your in the 79-80 mph range, so ya it’s very probable your intake has pulled away. It would be better if the sealant let go around your transom, but I’m betting it’s your intake. My...
  13. Replies
    31
    Views
    1,577

    Yikes, that does not look good! Are you stock?

    Yikes, that does not look good! Are you stock?
  14. Replies
    31
    Views
    662

    They sell those same plastic valves at HD

    They sell those same plastic valves at HD
  15. Replies
    31
    Views
    662

    It’s metric but 5/8 fittings work just fine I...

    It’s metric but 5/8 fittings work just fine
    I think I would use a plastic ball valve, a brass 5/8 I would think would be huge
  16. Thread: Yamaha Svho

    by BLASTER 1
    Replies
    5
    Views
    261

    Humm, I googled it and couldn’t find anything for...

    Humm, I googled it and couldn’t find anything for the Yamaha, just the SD
  17. Thread: Yamaha Svho

    by BLASTER 1
    Replies
    5
    Views
    261

    View Post

    Awe, I didnít know they made them. I only knew of the R&D version
    Thanks, now I want one LOL
  18. Thread: Yamaha Svho

    by BLASTER 1
    Replies
    5
    Views
    261

    I’m not sure what the et water jacket is. Can you...

    I’m not sure what the et water jacket is. Can you explain in more detail or post a picture. Thanks
  19. Replies
    7
    Views
    294

    Stick with the 19 plate and have Jim modify it...

    Stick with the 19 plate and have Jim modify it then get the Riva grate and you’ll be one Happy Camper!
  20. Replies
    9
    Views
    442

    Try this place ...

    Try this place

    https://www.yamahasportsplaza.com/oemparts/a/yam/5003a796f870021f60a13eed/electrical-1
  21. Replies
    9
    Views
    442

    Humm, I wonder if your ecu was fried

    Humm, I wonder if your ecu was fried
  22. After you get the fuel assembly out and install...

    After you get the fuel assembly out and install the Riva parts I used a very flexible piece of wire to compressed and tie the fuel assembly into a shorter unit
    It makes reinstalling a piece of...
  23. What became of your situation? Hopefully...

    What became of your situation?
    Hopefully everything worked out
  24. Replies
    3
    Views
    206

    And it’s just below and to the rear of the intake...

    And it’s just below and to the rear of the intake manifold
  25. Replies
    1
    Views
    158

    View Post

    I only know of this one, Iím using the worx cooling fitting instead of the anode. Itís right where the 90 elbow and hose clamp is
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4