Search

Type: Posts; User: Pwgsx

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    30
    Views
    3,358

    FS - Parts Have any left? I want to match the yellow from a...

    Have any left? I want to match the yellow from a 2016 RXPX.
  2. Replies
    5
    Views
    1,397

    Hoping to check on Sunday!

    Hoping to check on Sunday!
  3. Replies
    5
    Views
    1,397

    Waterlines are verified correct. If I run with...

    Waterlines are verified correct. If I run with the Rave Caps removed I should get peak RPMs just crappy bottom end right? That would verify that the Rave solenoid is bad? The Raves came rebuilt...
  4. Replies
    5
    Views
    1,397

    951 Only Getting 5600 rpms

    Backstory: A buddy acquired a non working 98 GSX Limited that had a bad motor. He went with a rebuilt motor and is now running premix. Carbs were rebuilt using genuine kits and pop off was set...
  5. Replies
    0
    Views
    117

    WTB - Parts WTB- 951 Airbox Metal Tab

    Missing the metal tab on the airbox. Anyone have one? :lol:http://greenhulk.net/forums/attachment.php?attachmentid=453924&stc=1
  6. Replies
    4
    Views
    304

    I was thinking the kill switch but it only kills...

    I was thinking the kill switch but it only kills one engine, the other keeps running.
  7. Replies
    4
    Views
    304

    230SX - Engine keeps dying

    My neighbor has a 2008 Yamaha 230sx, It will run good at high speed for several seconds but then one engine dies, dead in the water. The other engine keeps running just fine. The engine will start...
  8. Replies
    13
    Views
    692

    I have a 2016 RXPS, 35 hrs and have metal flecks....

    I have a 2016 RXPS, 35 hrs and have metal flecks. Not as many as you but they are there. I was told it was normal last time I was talking with a seadoo tech.
  9. Just go to HD or amazon and buy this thread...

    Just go to HD or amazon and buy this thread extractor. Its used for broken sprinkler heads, works like a charm. ...
  10. Replies
    59
    Views
    4,057

    I would sell them for what they are and find...

    I would sell them for what they are and find something that was not used in salt water. You will have a fun time if you ever remove the pump and who knows about all the corrosion on the electronics,...
  11. Thread: Winterize 300

    by Pwgsx
    Replies
    4
    Views
    592

    Mine is stored in a garage in TX but I flushed...

    Mine is stored in a garage in TX but I flushed with the pink stuff on both sides and then blew it out with air. Removing the air inlet hose is a PITA but its just to remove any condensation that...
  12. Replies
    1
    Views
    293

    Posting in the correct section might help ;)

    Posting in the correct section might help ;)
  13. And place any shims that were removed in the same...

    And place any shims that were removed in the same spots.
  14. Replies
    6
    Views
    445

    My old gsx limited ran at 120 psi for 2 years and...

    My old gsx limited ran at 120 psi for 2 years and I sold it. Last I heard its still running!
  15. Replies
    8
    Views
    554

    I put another new solenoid in this morning and...

    I put another new solenoid in this morning and still get nothing. Itís putting 12v to the starter side when start button is pressed but nothing happens. Starter does spin if I just jump the solenoid....
  16. Replies
    6
    Views
    445

    121 taint bad. I would clean and rebuild the...

    121 taint bad. I would clean and rebuild the carbs and change the fuel lines. Also "sleds" is more of a term for a ski-doo ;)
  17. Replies
    4
    Views
    441

    yep, just tighten down the screw tops with some...

    yep, just tighten down the screw tops with some pliers.
  18. Replies
    8
    Views
    554

    Ok so I’m bypassing the kill switch even though I...

    Ok so I’m bypassing the kill switch even though I tested and it works. The start button works as well. If I put my tester on the starter side of the solenoid and press the start button I get 12v to...
  19. Replies
    8
    Views
    554

    ?? uhhh ok but I was talking about re wiring...

    ?? uhhh ok but I was talking about re wiring what the p.o. had made of these wires which was a rats nest. I understand the testing process. Jumping to conclusions like a female I see ;)
  20. Replies
    8
    Views
    554

    So the kill switch is a closed circuit to start...

    So the kill switch is a closed circuit to start and when the tether is pulled its open and shuts the ski off? I HATE trying to re-wire these boxes after someone has gone through and messed with...
  21. Replies
    2
    Views
    287

    Pop the vts cover off, grab some grease and pack...

    Pop the vts cover off, grab some grease and pack that whole housing full. Then slap the cover back on. I did this on a 04 rxp and never had to worry about it again. Water cannot displace the...
  22. Replies
    8
    Views
    554

    94 gtx- Wont Crank

    I acquired a 94 GTX that was told it doesnt run or turn over. I got it home and popped in a new battery and nothing. Jumped the solenoid and it turns over with even 155 compression. I did some...
  23. Replies
    8
    Views
    561

    I splash some water on the bars before I ride and...

    I splash some water on the bars before I ride and it goes away for the day. Seems to come from the plastics rubbing.
  24. Same here on my 2016. I ended up using a dremel...

    Same here on my 2016. I ended up using a dremel to remove the gel coat around each drilled hole and grinded out any cracking so it wont spread. Its sad to see all the cut corners thru out the years.
  25. Replies
    5
    Views
    258

    Sell it, its a Kawasuckie!

    Sell it, its a Kawasuckie!
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4