Search

Type: Posts; User: toxicgun

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    7
    Views
    408

    I routed my breather out of a through hull on...

    I routed my breather out of a through hull on mine, mine is below water line, see to be working good for me, your hose is plenty big enough.
  2. Replies
    4
    Views
    279

    are you looking for a shipping purpose?

    are you looking for a shipping purpose?
  3. Replies
    4
    Views
    356

    no marrying on an 03

    no marrying on an 03
  4. Replies
    15
    Views
    614

    agreed, no reason to remove cylinder head.

    agreed, no reason to remove cylinder head.
  5. Thread: 215 flywheel

    by toxicgun
    Replies
    3
    Views
    256

    WTB I didnt realize you pm ed me.

    I didnt realize you pm ed me.
  6. Replies
    8
    Views
    328

    talk to me, what prop? how hard on the stator is...

    talk to me, what prop? how hard on the stator is it? I am killing my stator housing with a 15/24, I dont think i can force more water through it.
  7. Replies
    4
    Views
    356

    bite the bullet and replace it. Is it bad like...

    bite the bullet and replace it. Is it bad like not powering something up?
  8. Replies
    15
    Views
    614

    did it spin the thrust bearing? Trash it if it...

    did it spin the thrust bearing? Trash it if it did, otherwise replace the bearings and probably the crank.
  9. Replies
    5
    Views
    639

    FS location?

    location?
  10. Thread: 215 flywheel

    by toxicgun
    Replies
    3
    Views
    256

    WTB got one for $100 if you still need one.

    got one for $100 if you still need one.
  11. for sure has been hydrolocked, you probably have...

    for sure has been hydrolocked, you probably have a bent rod, you will know in about 8-10 hours of riding. I would bust out a dial indicator and check for a bent rod.
  12. Replies
    9
    Views
    704

    FS - Parts that sucks balls

    that sucks balls
  13. Replies
    4
    Views
    386

    WTB - Parts how much are you asking?

    how much are you asking?
  14. spark, fuel, and compression, which one are you...

    spark, fuel, and compression, which one are you missing? I agree with above, sounds like it was sank and they cranked the piss out of it. May want to check that the rods arent bent from hydrolocking
  15. Replies
    0
    Views
    86

    WTB - Parts gp1200r stainless steel intake grate

    cash on hand, need one ss800 intake grate is the one I am looking for
  16. Replies
    9
    Views
    704

    FS - Parts looks like a pretty decent deal but that chipped...

    looks like a pretty decent deal but that chipped blade is going to be a problem. Replace the center section whomever buys it.
  17. that engine was under water it looks like. Check...

    that engine was under water it looks like. Check the casting numbers, it may be an older engine someone put in that ski. The older engines had sodium filled valves that liked to snap off.
  18. Replies
    2
    Views
    308

    SOLD did you take a roloc wheel to the gasket area? ...

    did you take a roloc wheel to the gasket area? Looks like circular swirls from a roloc or sander of some sort
  19. my gpsho ran 78gps on a completely stock setup...

    my gpsho ran 78gps on a completely stock setup with no tune with a 14/21 and I am pretty sure it is sitting on the rev limiter.
  20. Thread: Gp1200r parts

    by toxicgun
    Replies
    11
    Views
    688

    FS - Parts is the intake grate stainless or aluminum?

    is the intake grate stainless or aluminum?
  21. Replies
    13
    Views
    1,010

    it will technically run but not correctly at all....

    it will technically run but not correctly at all. I have personally tried it.
  22. Replies
    1
    Views
    161

    WTB - Parts standard bore?

    standard bore?
  23. Replies
    7
    Views
    316

    balance technology in livermore california does...

    balance technology in livermore california does mine.
  24. Replies
    3
    Views
    200

    Thanks, being that it is your old setup I will...

    Thanks, being that it is your old setup I will take your advise. I was planning on trying .020 but I will go with what you were doing since that was working.
  25. Replies
    3
    Views
    200

    4tec turbo guys spark plug gap question

    anything past 18psi is stumbling, I am suspecting the factory gap is too much. What are you guys running? Of course I have done new plugs and coils, doesnt seem to matter. running 11.5 currently...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4