Search

Type: Posts; User: Joshbot007

Page 1 of 3 1 2 3

Search: Search took 0.03 seconds.

  1. It is brand new. It just appears that when they...

    It is brand new. It just appears that when they pressed it together that the seals are tight against the inner race of the bearing causing more friction but I wonder if they are supposed to be tight...
  2. How freely Is the bearing in these supposed to...

    How freely Is the bearing in these supposed to spin? I found a killer deal on a wsm one that was the full assembly for the price of the empty wsm so I figured Id try it and if I didnít like it press...
  3. I am located in Hershey PA. I already pulled the...

    I am located in Hershey PA. I already pulled the motor, it didnít take much more then an hour as Im pretty good with working on things
  4. I blocked the oil pump off and bypassed the...

    I blocked the oil pump off and bypassed the lines. I was told that bypassing the coolant lines is fine as per a post I made here about a month ago. Do you agree with that?
  5. Replies
    1
    Views
    83

    No one has any experience with these?? Good or...

    No one has any experience with these?? Good or bad? I wanna pull the trigger and get it asap because I have to replace the stator gasket anyway but I wanna make sure Im not missing any big smoking...
  6. Thanks! I already removed the engine prior to...

    Thanks! I already removed the engine prior to reading this sorry but I wanted to check the motor mounts anyway. I will use the “right stuff”. As for the motor mounts they look good in my hand and...
  7. Ok thanks! As far as the sealant goes Im a bit...

    Ok thanks! As far as the sealant goes Im a bit confused. I heard people say to use epoxy and I can see epoxy from underneath the ski right now, some say use just silicone, and some permatex which i...
  8. Replies
    1
    Views
    83

    1100 zxi timing advance kit/plate

    I have to take my motor out to replace my driveshaft holder,bearings, and seals. While I had it out I figured it would be an opportune time to put on a timing advance plate so I started to do some...
  9. In addition to my last reply, has anyone tried...

    In addition to my last reply, has anyone tried just the aftermarket holder itself? The reason I ask is oem kawasaki holders are $250+ where the aftermarket are sub 100. I would use oem seals and...
  10. Thanks! I will go oem and check the mounts. Im...

    Thanks! I will go oem and check the mounts. Im wondering if I don’t see any problem with the mounts are they good or does the rubber get soft with age and allows more movement?
  11. Sounds good! Does anyone know if the sbt...

    Sounds good! Does anyone know if the sbt preassembled ones are any good or are the bearings and seals junk? Also do the motor mounts in these skis go bad? Wondering if excessive motor mount movement...
  12. 1100 Zxi though drive line plate spinning

    The outer race that the seals and bearings go into is spinning inside the metal plate. Is this normal? I had a problem on my last ride where I seemed to be getting a lot of driveline resistance....
  13. Replies
    0
    Views
    97

    1100 zxi waterbox mod help

    So I got my waterbox out with the hope of modifying it with that whole 1.5in hole saw through the baffle thing. I wasnít really sure how to do it but figured once I got it off It would be pretty self...
  14. Replies
    0
    Views
    134

    WTB - Parts WTB 1100 zxi TDR spray waterbox

    All,

    If anyone has lying around or does not want their TDR Waterbox Spray Type I would love to buy and try this exhaust!

    Thanks,
    Josh
  15. Replies
    14
    Views
    429

    Do you guys/do I have to use the spacers that go...

    Do you guys/do I have to use the spacers that go between the intake grate and the pump shoe? (Part number 92026-3731). Mine were rusted so bad I had to do all kinds of stuff to get the grate removed...
  16. Replies
    14
    Views
    410

    While you have the carbs off check that pulse...

    While you have the carbs off check that pulse line that goes from cyl 1-3 right below them. That line is responsible for making the fuel pumps work and if cracked would cause problems.

    also since...
  17. Replies
    14
    Views
    410

    My 96 zxi did something very similar when I...

    My 96 zxi did something very similar when I replaced the fuel pump diaphragms with ebay units. I ended up buying the sbt kit and put that in and completely fixed it. I know you said accelerator...
  18. Replies
    14
    Views
    429

    Well looks like I installed the one backwards....

    Well looks like I installed the one backwards. Guess I should just replace them both again right? Idk how to get them out without messing them up.
  19. Replies
    14
    Views
    429

    Ok thanks! So I was rebuilding the pump...

    Ok thanks!

    So I was rebuilding the pump tonight and I ran into two issues.

    1) are you sure that that is the correct orientation of the seals? With the smaller one being flat face up and the...
  20. Replies
    14
    Views
    429

    I had no idea about the grease in between the...

    I had no idea about the grease in between the seals and in the housing thanks!!! as far as the nose cone, is there anything theoretically wrong with running without it? I know it makes the ski a...
  21. Replies
    14
    Views
    429

    I got the kit and I found one bearing to be...

    I got the kit and I found one bearing to be leaking and the other to have noticeable pits in it when rotating it by hand... Sooooo I just returned it and ordered everything OEM on ebay with New Old...
  22. Thanks! I will opt to keep them off because one...

    Thanks! I will opt to keep them off because one less way for water to potentially leak into the case I figure is the better! Unless my ski tells me otherwise some day by eating a stator they will...
  23. Can the stator cover coolant lines be removed?

    Last summer I deleted my oil pump and read that the coolant lines could be removed too because they are for cooling the oil pump bearing.

    Now a year later reading random posts I saw that...
  24. Replies
    14
    Views
    429

    Thanks! I got a kit but it seems to be generic...

    Thanks! I got a kit but it seems to be generic and from what I can tell look like all the rest. The SBT kit uses (at least from the picture) Chinese bearings so I’m not aure it would be any better...
  25. Replies
    14
    Views
    429

    1100 zxi pump rebuild questions

    So I am in the process of rebuilding my pump with a new pump rebuild kit, impeller shaft, seals, impeller, and wear ring (impeller came loose and wore a nice ring in the wear ring). I just about know...
Results 1 to 25 of 63
Page 1 of 3 1 2 3