Search

Type: Posts; User: yama-doo

Page 1 of 3 1 2 3

Search: Search took 0.03 seconds.

  1. what size are the four bolts on the back side that screw the mpem mounting plate?

    what size are the four bolts on the back side that screw the mpem mounting plate to the hull?

    I would have thought it be 10mm like almost everything else but...
  2. exhuast help/advice needed on a seadoo hx conversion with a gsx limited 947 engine

    hey guys its been a few years since I played with my skis or projects , but I'm getting motivated again and pulled out my old HX project I thought it be simpler and faster to just scrap the idea of...
  3. Replies
    11
    Views
    1,463

    so the starter it self was your problem? (I ask...

    so the starter it self was your problem? (I ask becuase it sounds like same issue I am having)
  4. Replies
    8
    Views
    5,727

    my gsxl seems like to much compression to spin...

    my gsxl seems like to much compression to spin over so I search to see what other people had similar issues but I can now tell you those carbs can be removed blind and leaving that pipe in place ,...
  5. Well no one answered and I was not able to find...

    Well no one answered and I was not able to find those brackets so I picked up some tube and gathered some scrap I had laying around and made my own , I ran out of argon about 1/3rd of the way through...
  6. where to find trailer parts and accessory ideas 5 place trailer

    ok I have a couple questions for right now and I'm also looking for some ideas for the near future for trailer accessory like BBQ grill and large roll out shade awning ?????


    Questions: ...
  7. Replies
    0
    Views
    336

    HELP , 99 GSX limted

    I have two confusing problems maybe someone has some ideas to help (i'm new to seadoos)

    1) engine will not turn over when pushing start button , battery is charged , new ground wire, when I...
  8. got it 1) batt 15a 2) MPEM 5a 3) VTS ...

    got it

    1) batt 15a
    2) MPEM 5a
    3) VTS 7.5a
    4) spare
    5) spare
    6) acc (bilge pump) 3a

    (rear box one fuse 20a) got it
  9. Help seadoo gsx limited fuse panel , which slot for which fuse?????

    I downloaded the 99 gsx limited manual, it tells me there are six fuses and the proper size fuse for each system .......BUT.... there is no diagram for which slot is for what...
  10. thanks

    thanks
  11. yamaha 1100 water cooling hose routeing help needed

    This is on my sons project B1 blaster ski we put (are slowly putting) in a 96/97 waveradier 1100cc engine in the B1. I'm a little confused with the water cooling hose routing on the engine. I am...
  12. Replies
    0
    Views
    427

    Yamaha wireing harness questions / help

    couple questions;


    1) yamaha B1 blaster the wiring harness coming down form handle bars has two plugs (one white one black) i need to find one of the white plugs (red/brow wires) form the engine...
  13. thanks

    thanks
  14. WFO, yep have the rod I need the ball ends that...

    WFO,
    yep have the rod I need the ball ends that snap into the rod
  15. I actual tried but none of the carb diagrams I...

    I actual tried but none of the carb diagrams I looked at had the actual linkage it was just show the single carb disassemble unless I looked in wrong place. That picture is different type then I...
  16. little help --- proper name carb linkage parts

    I need a little help what is the proper name carb linkage parts , where the rod connects all three carb to the throttle plate, I am calling this a "ball joint" but there has to be a proper name for...
  17. Replies
    3
    Views
    394

    I was use the 25-30 psi as a example that the...

    I was use the 25-30 psi as a example that the gauge it self holds pressure. my carb pop off should be 32psi

    no what I was trying to say is when I attach the pop off gauge to the carb and try to...
  18. Replies
    3
    Views
    394

    pop-off guage problem / question

    I have one of the thumb pump pop-off gauges , I changed the 1/8 hose to 1/4" to work with my carbs all that is good if I hold finger over hose and pump to 25-30psi it holds fine until I release so...
  19. thanks for the tip

    thanks for the tip
  20. going to try the upholstery shops after the...

    going to try the upholstery shops after the holidays
  21. didn't find any good foam only thing I saw was...

    didn't find any good foam only thing I saw was some 1/2" open cell foam , guess I have to look some more after the holidays
  22. thanks , I'm headed to town now to look for foam...

    thanks , I'm headed to town now to look for foam an ss staples
  23. hey what length stainless staples did you use to...

    hey what length stainless staples did you use to put the new cover on with?? 3/8", 5/16" ,1/4"
  24. ya well I gotta use the seat now days I have a...

    ya well I gotta use the seat now days I have a bad leg if I try ti stand someone has to carry me ashore when I go in cuase I will not be able to walk .

    do you think shore like Micheals sells...
  25. lol....no if mine looked that good I probably...

    lol....no if mine looked that good I probably wouldn't even worry about it


    here is what mine looks like the foam stuff you can see is that dry rotted stuff that just powders up and cumbumles...
Results 1 to 25 of 67
Page 1 of 3 1 2 3