Search

Type: Posts; User: BlueFishCrisis

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Sticky: I know this is old, but for future readers, the...

    I know this is old, but for future readers, the high speed cap is simply pulled off with a pair of needle nose pliers.
  2. Replies
    2
    Views
    160

    Where did you get the stator?..... Aftermarket...

    Where did you get the stator?.....

    Aftermarket Stators have been questionable....
  3. Replies
    0
    Views
    79

    Fuji Parts for sale!!

    Parts liquidation!! If you have a 650-750-780 and need parts - Let me know!!
  4. Get an OEM stator.

    Get an OEM stator.
  5. Replies
    6
    Views
    170

    With the motor out I would definitely rebuild the...

    With the motor out I would definitely rebuild the carbs and inspect your reeds for wear and cracking...
  6. I helped develop the Arieltek CDIs for Polaris...

    I helped develop the Arieltek CDIs for Polaris machines. The no start / backfire was not one of the issues I found with the CDI.

    The Aftermarket stators however have been known to come out of...
  7. Replies
    2
    Views
    134

    https://i.ebayimg.com/images/g/7WQAAOSwUm5cJOzB/s-...

    https://i.ebayimg.com/images/g/7WQAAOSwUm5cJOzB/s-l1600.jpg
  8. Replies
    10
    Views
    423

    Video is out of the water and doesn't say...

    Video is out of the water and doesn't say much..... If on the water, as xlint amd sldvx said you are running lean....
  9. Replies
    11
    Views
    342

    The SL hull was used in 97 for the 780, 700, 900,...

    The SL hull was used in 97 for the 780, 700, 900, and 1050. Not sure if it was the same hull or not, but the 700 would be a drop in for the 780 mount locations. The rears should be fine, but the...
  10. Replies
    3
    Views
    200

    Pull the MFD out and disconnect the harness from...

    Pull the MFD out and disconnect the harness from the back. You will see the 6 different color wires in the harness. These all enter the Ebox in the same spot. Check each wire for continuity to...
  11. Replies
    3
    Views
    200

    This is for setting the timing by viewing marks...

    This is for setting the timing by viewing marks on the it as it spins. No oil, or any fluids for that matter, should be present where the flywheel is.
  12. Replies
    14
    Views
    199

    Lots to do, starting with Rebuild the carbs. ...

    Lots to do, starting with Rebuild the carbs. Then tune them... It will cost $$$$
  13. Replies
    1
    Views
    81

    No pump oil. Ignition can be an issue. Trailer...

    No pump oil. Ignition can be an issue. Trailer is worth 2-300. You will be working on it....
  14. IF not pump could be bendix....

    IF not pump could be bendix....
  15. Replies
    2
    Views
    101

    No it doesn't. I strongly suggest you do not...

    No it doesn't. I strongly suggest you do not connect the tan wire to the gray terminal on the board as that is for the rev limiter on a SLT 780, which you do not have. You should connect the tan...
  16. The kit came with larger jet sizes, and didn't...

    The kit came with larger jet sizes, and didn't suggest alternate needle settings after install.. What size jets did you install? There is never a magic carb setting, just a starting point. You...
  17. Replies
    13
    Views
    306

    The thermostat can be removed, but as Xlint...

    The thermostat can be removed, but as Xlint stated, and I stated earlier, a holed piston is not likely a result of an overheated motor due to lack of cooling. Do a leak down test to determine if...
  18. Replies
    42
    Views
    791

    Try running a ground from the battery direct to...

    Try running a ground from the battery direct to the ground terminal in the ebox. This will bypass the ground from the stator to the ebox which is buried in a wire harness and can be burnt.... I...
  19. 1/4" id is proper. Recommend black...

    1/4" id is proper. Recommend black braided/reinforced fuel line in lieu of the clear stuff. Hose clamps hold on better and the wall is more crush resistant.
  20. Replies
    13
    Views
    306

    A hole in a piston isn't necessarily a result of...

    A hole in a piston isn't necessarily a result of overheating as much as running lean. When you get back on the water be sure to perform plug chops and check piston wash. Plug chops consist of...
  21. Do you mean while the engine is running? Oil...

    Do you mean while the engine is running? Oil will only travel to the carbs with the engine running. It moves slow, but if you disconnect the line from the carb while the engine is running and the...
  22. Replies
    22
    Views
    2,222

    :smt038:cartman:

    :smt038:cartman:
  23. I don't think there is a need to flip them, but...

    I don't think there is a need to flip them, but definitely make sure the restrictor is there, and use Tygon fuel lines, not standard rubber when you replace the lines in the tank. The Tygon lines...
  24. Replies
    8
    Views
    1,740

    I had a TDR and removed it after a day at the...

    I had a TDR and removed it after a day at the lake. Unfortunately for me, all noise and no go.

    Now I have trippple pipes on my 780. Lots of noise and tons of go!!...
  25. Thread: SLT 780

    by BlueFishCrisis
    Replies
    4
    Views
    332

    What he said... or what Myself said

    What he said... or what Myself said
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4