Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    178

    WTB - Parts This one is a '99. I only NEED one but would take...

    This one is a '99. I only NEED one but would take 2 so I have one around next time.
  2. Replies
    6
    Views
    307

    A 4 stroke crankcase isn't really completely...

    A 4 stroke crankcase isn't really completely sealed and holding pressure like a 2 stroke case. Everywhere oil goes would need blocked off...valve cover, tip over switch, dipstick tube, output shaft,...
  3. Replies
    3
    Views
    75

    Most likely places on on old 650 will be the mid...

    Most likely places on on old 650 will be the mid shaft seals, and the old fiberglass waterbox.
  4. I had a customer with an LS2000 that ran great...

    I had a customer with an LS2000 that ran great after I did pumps and carb mods.
    I have another customer with a twin engine Exciter that I need to tune in this spring.
    They really are strong when...
  5. Replies
    8
    Views
    406

    Anything boosted will NOT run right with a non...

    Anything boosted will NOT run right with a non boost ecu. The computer cannot compensate. Maybe he's done spending money cause he bought the wrong ecu.......you'll never get the truth about that lol!
  6. Replies
    8
    Views
    386

    When I've done it they were so close that just a...

    When I've done it they were so close that just a wee bit with a flat bastard file was all that was needed. You gotta clamp it after the sleeve goes in though. They do tend to try and rise up.
  7. Replies
    20
    Views
    604

    Yes! That is a known issue and common failure...

    Yes! That is a known issue and common failure mode. Perform the balanced return mod to keep that from happening.
  8. Replies
    20
    Views
    604

    Hard to see the check discs with the glare but if...

    Hard to see the check discs with the glare but if they are still flat with no little creases anywhere they're good. Sounds likely you were sucking air around the base gasket.
  9. Replies
    8
    Views
    386

    Yes. All non pv 1200's are the same. Suv uses the...

    Yes. All non pv 1200's are the same. Suv uses the 65u just like 97-99 GP1200.
  10. Replies
    20
    Views
    604

    The pump side, 2 little round discs with a little...

    The pump side, 2 little round discs with a little rubber center.
  11. Replies
    20
    Views
    604

    Yes, an air leak at the carb base will cause a...

    Yes, an air leak at the carb base will cause a lean condition. Pop the cast rectangular cover on that center carb. Let's see the round check discs.
  12. Replies
    9
    Views
    275

    And here is the finished guage reinstalled with a...

    And here is the finished guage reinstalled with a new face decal. I had trouble getting a good pic cause of glare and reflection but it's now plainly legible again. =D>
  13. Replies
    9
    Views
    275

    Next everything got put back together with a...

    Next everything got put back together with a little bit of marine epoxy I had, then lightly clamped for 48 hours.
  14. Replies
    9
    Views
    275

    I used a very small flat blade screwdriver with...

    I used a very small flat blade screwdriver with tape over the tip to carefully pry the lcd out of the housing. It has to tilt a bit, the top (opposite the white strip) has to come up a bit first. In...
  15. Replies
    9
    Views
    275

    And when the board is removed it looks like...

    And when the board is removed it looks like this!! The gold rectangle is the gauge background. You could cut a piece of any color graphic vinyl and change this if you want to customize. The white...
  16. Replies
    9
    Views
    275

    When you get it open there are 5 small phillips...

    When you get it open there are 5 small phillips head screws that need removed.
  17. Replies
    9
    Views
    275

    I used a dremel with a cutoff wheel to cut around...

    I used a dremel with a cutoff wheel to cut around the edge just behind the face.
  18. Replies
    9
    Views
    275

    Ultra 150 & STXr guage repair

    I've done several Seadoo gauges and thought I'd give a Kawi gauge a try. I verified this guage was still working with a strong flashlight and my polarized sunglasses. I could just make out most of...
  19. Replies
    8
    Views
    386

    Yep, I've dropped out sleeves before on Seadoo...

    Yep, I've dropped out sleeves before on Seadoo and Yamaha. As stated about 400-450 in the barbeque grill for 30-45 minutes. You need a stand and a couple wood blocks handy to lay the cylinder on....
  20. Replies
    20
    Views
    604

    All 3 are lean, center especially lean. Pull the...

    All 3 are lean, center especially lean. Pull the carbs and check that center one for creased fuel pump check valves. It's a well known and documented issue on the 65u 1200. It needs the balanced...
  21. Replies
    2
    Views
    178

    WTB - Parts Need Ultra 150 STXr exhaust bolt

    I need one or two of the 6" long bolts that hold the expansion chamber to the middle of the engine. Anyone got some laying around??
  22. WTB - Parts Cases are machined as a matched set. Bad idea to...

    Cases are machined as a matched set. Bad idea to just replace one half. Any local welding shop can repair the hole for you. I have them done every season on one or two.
  23. Replies
    20
    Views
    604

    Look for a loose oil line or creased fuel pump...

    Look for a loose oil line or creased fuel pump check valves on center cylinder.
  24. All 1100's had the 155 pump. To really harness...

    All 1100's had the 155 pump. To really harness the power of that 1100 you will need to swap the pump.
  25. Replies
    3
    Views
    195

    WTB - Parts I had trouble once finding an early ecu. I bought...

    I had trouble once finding an early ecu. I bought one from another model I got a deal on and had it remapped. Several companies can do that, just fyi.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4