Search

Type: Posts; User: toxicgun

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    4
    Views
    338

    no marrying on an 03

    no marrying on an 03
  2. Replies
    15
    Views
    576

    agreed, no reason to remove cylinder head.

    agreed, no reason to remove cylinder head.
  3. Thread: 215 flywheel

    by toxicgun
    Replies
    3
    Views
    230

    WTB I didnt realize you pm ed me.

    I didnt realize you pm ed me.
  4. Replies
    8
    Views
    319

    talk to me, what prop? how hard on the stator is...

    talk to me, what prop? how hard on the stator is it? I am killing my stator housing with a 15/24, I dont think i can force more water through it.
  5. Replies
    4
    Views
    338

    bite the bullet and replace it. Is it bad like...

    bite the bullet and replace it. Is it bad like not powering something up?
  6. Replies
    15
    Views
    576

    did it spin the thrust bearing? Trash it if it...

    did it spin the thrust bearing? Trash it if it did, otherwise replace the bearings and probably the crank.
  7. Replies
    5
    Views
    599

    FS location?

    location?
  8. Thread: 215 flywheel

    by toxicgun
    Replies
    3
    Views
    230

    WTB got one for $100 if you still need one.

    got one for $100 if you still need one.
  9. for sure has been hydrolocked, you probably have...

    for sure has been hydrolocked, you probably have a bent rod, you will know in about 8-10 hours of riding. I would bust out a dial indicator and check for a bent rod.
  10. Replies
    9
    Views
    688

    FS - Parts that sucks balls

    that sucks balls
  11. Replies
    4
    Views
    382

    WTB - Parts how much are you asking?

    how much are you asking?
  12. spark, fuel, and compression, which one are you...

    spark, fuel, and compression, which one are you missing? I agree with above, sounds like it was sank and they cranked the piss out of it. May want to check that the rods arent bent from hydrolocking
  13. Replies
    0
    Views
    86

    WTB - Parts gp1200r stainless steel intake grate

    cash on hand, need one ss800 intake grate is the one I am looking for
  14. Replies
    9
    Views
    688

    FS - Parts looks like a pretty decent deal but that chipped...

    looks like a pretty decent deal but that chipped blade is going to be a problem. Replace the center section whomever buys it.
  15. that engine was under water it looks like. Check...

    that engine was under water it looks like. Check the casting numbers, it may be an older engine someone put in that ski. The older engines had sodium filled valves that liked to snap off.
  16. Replies
    2
    Views
    305

    SOLD did you take a roloc wheel to the gasket area? ...

    did you take a roloc wheel to the gasket area? Looks like circular swirls from a roloc or sander of some sort
  17. my gpsho ran 78gps on a completely stock setup...

    my gpsho ran 78gps on a completely stock setup with no tune with a 14/21 and I am pretty sure it is sitting on the rev limiter.
  18. Thread: Gp1200r parts

    by toxicgun
    Replies
    11
    Views
    681

    FS - Parts is the intake grate stainless or aluminum?

    is the intake grate stainless or aluminum?
  19. Replies
    13
    Views
    999

    it will technically run but not correctly at all....

    it will technically run but not correctly at all. I have personally tried it.
  20. Replies
    1
    Views
    158

    WTB - Parts standard bore?

    standard bore?
  21. Replies
    7
    Views
    312

    balance technology in livermore california does...

    balance technology in livermore california does mine.
  22. Replies
    3
    Views
    197

    Thanks, being that it is your old setup I will...

    Thanks, being that it is your old setup I will take your advise. I was planning on trying .020 but I will go with what you were doing since that was working.
  23. Replies
    3
    Views
    197

    4tec turbo guys spark plug gap question

    anything past 18psi is stumbling, I am suspecting the factory gap is too much. What are you guys running? Of course I have done new plugs and coils, doesnt seem to matter. running 11.5 currently...
  24. WTB so you want to exchange your old parts for the...

    so you want to exchange your old parts for the parts you need? Just modify the sho exhaust pipe yourself, use the rest of the 1200/1300 exhaust with it.
  25. Replies
    14
    Views
    1,097

    Yep, I tried that, sucked down under boost.

    Yep, I tried that, sucked down under boost.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4