Search

Type: Posts; User: car22car

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    9
    Views
    170

    Thanks for the help but I don't know what you...

    Thanks for the help but I don't know what you mean by squish angle. How do you determine that. I did notice that the pistons that are in it are slightly above the bottom of the ports. Maybe this is...
  2. Replies
    9
    Views
    170

    Thanks

    Thanks
  3. Replies
    9
    Views
    170

    You are right again. They are steel. They look so...

    You are right again. They are steel. They look so close the the same as nikisal, So in this case do you use pistons for a red 1200. Also what would be the proper cylinder to piston clearance and the...
  4. Replies
    9
    Views
    170

    I will check that out and get back to you.

    I will check that out and get back to you.
  5. Replies
    9
    Views
    170

    You must be 100% correct on the red engine piston...

    You must be 100% correct on the red engine piston because a 1.5mm or 1mm over msx would not fit. Just don't understand the oversized cylinder. Can it wear that much because I am almost positive that...
  6. Replies
    9
    Views
    170

    Msx 140 rebuild.

    Going to rebuild another msx 140. Any recommendations on the best top end rebuild kit? Sbt,pwc,wsm? What do you guys use? Also when I pulled the heads ,I measured the bores. 2 are close to the 85mm...
  7. Replies
    2
    Views
    116

    Thanks K for the recommendation. Your help is...

    Thanks K for the recommendation. Your help is always appreciated.
  8. Replies
    2
    Views
    116

    Keihin carburator kit

    Hey guys, need to rebuild a triple Keihin carburator for a 97 sl1050. Looking for recommendations as to were and what to buy, OEM or kits like SBT has non OEM. Thanks for the help.
  9. Replies
    23
    Views
    1,181

    Thanks I will take that into consideration. Just...

    Thanks I will take that into consideration. Just curious to why the have hose adapters on them if it's not good to do.
  10. Replies
    23
    Views
    1,181

    Thanks Rip, you put my mind at ease. That is what...

    Thanks Rip, you put my mind at ease. That is what it looks like. We got a week or two before the lakes open up here in wisconsin.Then I'll drop her in and see how she goes. Do you have a...
  11. Replies
    23
    Views
    1,181

    I did get the motor changed out. It was a...

    I did get the motor changed out. It was a learning experience for sure. Next one should be easier. I do have a question for you guys tho. The ski fired up right away no problem. The lakes are froze...
  12. Replies
    23
    Views
    1,181

    Thanks Pottsie for your offer. I will certainly...

    Thanks Pottsie for your offer. I will certainly look you up when needed
  13. Replies
    5
    Views
    270

    could prbly use the rectifier from the other...

    could prbly use the rectifier from the other motor and try that. Hate to burn up another stator. Is there a way to test them. Thanks for the help
  14. Replies
    5
    Views
    270

    the original stator was used after the rebuild...

    the original stator was used after the rebuild and that when it started burning them up.
  15. Replies
    5
    Views
    270

    HI K447,didn't know you would be on the yamaha...

    HI K447,didn't know you would be on the yamaha forums. The motor is a 3cyl 1200cc efi yamaha 2stroke. The rectifier has not been changed as far as I am aware. Ideas?
  16. Replies
    5
    Views
    270

    Yamaha lx210 jet boat

    Hello all. I had a motor rebuilt for a lx210 jet boat. Reinstalled the motor but it keeps burning out the electrical stator. It will run fine on a hose or idling in the water but you open it up and...
  17. Replies
    5
    Views
    477

    Are the later 03s also heavier? Do you recall the...

    Are the later 03s also heavier? Do you recall the difference in the ride plate.
  18. Replies
    5
    Views
    477

    I have an 03 here also. Been trying to see a...

    I have an 03 here also. Been trying to see a difference in them but they look identical. I have read on here they are better but sure can't tell a difference.
  19. Replies
    5
    Views
    477

    04 msx 140 part out

    Parting out a 04 msx 140. PM me if anyone needs anything. Thanks
  20. Replies
    0
    Views
    140

    Msx 140 short block value

    Hey guys, does anyone know what a fair price would be for a msx 140 bottom end with 47 hours on it. Great shape. Thanks
  21. Replies
    6
    Views
    393

    Thankyou for your help.

    Thankyou for your help.
  22. Replies
    6
    Views
    393

    Will a stator and a cdi from a 2000 ,700...

    Will a stator and a cdi from a 2000 ,700 hurricane work, or a 700 virage.
  23. Replies
    6
    Views
    393

    97 sl700 stator replacement

    Hey all!. Got a 97 sl700 with bad stator. It looks like the update kits are nolonger available. What other option is there out side of finding a original stator. Are there any skis that would be...
  24. Replies
    23
    Views
    1,181

    Thanks Randy . Any help is sure Appreciated. What...

    Thanks Randy . Any help is sure Appreciated. What should the compression run on these motors and how low before they need rebuilding.
  25. Replies
    23
    Views
    1,181

    Thanks I do have the manual and have been reading...

    Thanks I do have the manual and have been reading it.Just looking for suggestions on making it easier. I will get that hex wrench. Thanks.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4