Search

Page 1 of 8 1 2 3 4

Search: Search took 1.00 seconds.

  1. Here is a quick tip for anyone that comes across...

    Here is a quick tip for anyone that comes across this thread. Use a heat gun to warm up the coolant hose before pulling them off of the fittings. Not only will they come off much easier but they...
  2. Replies
    42
    Views
    468

    Well, my first question would be, if it ran...

    Well, my first question would be, if it ran crappy and had old gas WHY did we keep trying to ride it?? That's a VERY effective method of blowing up a 2 stroke. Probably has a completely crapped fuel...
  3. Replies
    22
    Views
    367

    Can always run a wsm one if you dont wanna drop...

    Can always run a wsm one if you dont wanna drop the rhaas
  4. I sometimes wonder how the rest of the world just...

    I sometimes wonder how the rest of the world just sits around and watches TV and plays Candy Crush.
    If Iím forced to watch a movie or TV with the family I am constantly thinking about the next step...
  5. I am a rookie in terms of mods but I have read...

    I am a rookie in terms of mods but I have read enough to know removing the stock spark arrestor and adding aftermarket ones cannot be done without modifying the carbs. In other words don't do it...
  6. Plugs look great, intercepter is clear and will...

    Plugs look great, intercepter is clear and will clean up your combustion chambers. Its really made for power valve engines and i could imagine it keeps them spotless. Both skis and two quads looked...
  7. Replies
    47
    Views
    857

    He meant for the very front, where the oil pump...

    He meant for the very front, where the oil pump was.
  8. Replies
    10
    Views
    307

    spinach, with the advice that pro1200 gave, I...

    spinach, with the advice that pro1200 gave, I think that you'll be good to go.

    I'm going to assume that the battery is the dealer installed, traditional lead acid battery with the small screw-in...
  9. Get a Shop Manual www.brpmanuals.com Do the...

    Get a Shop Manual www.brpmanuals.com

    Do the work yourself and know the work is done correctly!
  10. Time for a new dealer, if bringing your ski to...

    Time for a new dealer, if bringing your ski to this dealer causes you so much anxiety and stress. Over previous experiences, take it somewhere else.
  11. Replies
    19
    Views
    1,839

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=461310&stc=1http://greenhulk.net/forums/attachment.php?attachmentid=461311&stc=1
    I saw these a couple summers ago. Screw buying a 50-60k F150...
  12. Make sure the pump has been upgraded to the 300...

    Make sure the pump has been upgraded to the 300 style and leave it alone. Not sure what just a new shaft would do for you or if you just conveyed his message wrong but it needs the 300 kawi style...
  13. Replies
    92
    Views
    2,048

    Sticky: That`s why my dog will not fetch the bone for me...

    That`s why my dog will not fetch the bone for me after giving him a flea dip. All this time I thought he was sleeping....

    Thanks Seabrook you are the best lol lol
  14. Would have been better off putting a finger...

    Would have been better off putting a finger throttle on it.
  15. Replies
    11
    Views
    678

    Had yams all broken hull even a HO. nano is a...

    Had yams all broken hull even a HO. nano is a week material for see riding. to thin and it breaks on the pressure points where the inner hull is glued, there is not one bit of support in the bow only...
  16. Replies
    16
    Views
    850

    Very good advise sir, I found it with mirror was...

    Very good advise sir, I found it with mirror was able to guide it to the opening with some wire,and eased it out with a magnet!!459850459851
  17. Replies
    4
    Views
    275

    thanks for the April's fool joke, needed a laugh...

    thanks for the April's fool joke, needed a laugh after looking at my 401 balance today
  18. Replies
    5
    Views
    269

    No. You can't not remove it. The oil pump feeds...

    No. You can't not remove it. The oil pump feeds the three carbs as well as the counter balance shafts at the front and rear of the motor.
  19. Replies
    13
    Views
    651

    I will suggest that almost more important...

    I will suggest that almost more important (especially for salt water) than the specific grease brand/whatever is the use of bearing buddies instead of the factory dust caps on the axle hubs.

    I...
  20. I prefer solder over any type of crimping when...

    I prefer solder over any type of crimping when repairing wires/connectors on the electrical harness'. Applying the correct size of heat shrink will seal off the exposed wires and sometimes using the...
  21. Replies
    14
    Views
    1,003

    Pull it. Rebuild it. Enjoy summer. They aren't...

    Pull it. Rebuild it. Enjoy summer. They aren't complicated rebuilds and you will know them inside and out. Do carb rebuilds while its apart using ONLY genuine Mikuni rebuild kits.
  22. Replies
    76
    Views
    6,642

    My friends vx has the ride I like it but still...

    My friends vx has the ride I like it but still like my ultra lx better. I can live with a lever reverse and gain more comfort. More storage. More acceleration. Good trade off in my eyes
  23. Replies
    12
    Views
    662

    How about a little water to dissolve the salt? ...

    How about a little water to dissolve the salt? I'm not sure how you'd soak those bolts. But I've had some luck freeing up salt-bound parts by soaking them in water. After all, water does dissolve...
  24. turn your phone off and enjoy the day

    turn your phone off and enjoy the day
  25. --------------------------------- There can only...

    ---------------------------------
    There can only be one reason for this. You guys from the "Land Down Under" are upside down !!! :)

    Even the fresh water in your toilet bowls does not rotate work...
Results 1 to 25 of 198
Page 1 of 8 1 2 3 4