Search

Page 1 of 3 1 2 3

Search: Search took 1.00 seconds.

  1. Replies
    28
    Views
    1,656

    The gauge cluster rolls over at 1000. Below is a...

    The gauge cluster rolls over at 1000. Below is a pic of YDS on a high hour ski.
  2. Replies
    28
    Views
    1,656

    The total hours are calculated as a 16-bit...

    The total hours are calculated as a 16-bit unsigned integer, which is why it reads 655.36 max. Manually add up the RPM range hours to get the actual total hours.

    -Greg
  3. Replies
    3
    Views
    184

    SOLD Thanks. Picked up one local from 1_Fast_SHO just...

    Thanks. Picked up one local from 1_Fast_SHO just now. Thanks, guys!
  4. Replies
    6
    Views
    376

    Partially lower your reverse gate to slow you...

    Partially lower your reverse gate to slow you down at idle.
  5. Replies
    19
    Views
    965

    It's not that uncommon the 12F/15Fs to hear a...

    It's not that uncommon the 12F/15Fs to hear a tick. I would not worry about it, but at some point you should probably do a valve adjustment. Not all that hard, but a little trickier with the motor in...
  6. Replies
    8
    Views
    860

    Glad to see this turned out well. I share your...

    Glad to see this turned out well. I share your 'don't sell skis to neighbors' policy.

    As a general rule I try to not sell skis to people I know as I then feel responsible to help if something...
  7. Replies
    4
    Views
    463

    Should be reading 14+ at higher RPM. Make sure...

    Should be reading 14+ at higher RPM. Make sure the plug is fully inserted (clicked) into the voltage regulator. If it is, then try swapping out the voltage regulator for a known good unit.

    This...
  8. Replies
    41
    Views
    2,898

    The very early ones had an ECU issue that would...

    The very early ones had an ECU issue that would cause a lean condition in hot weather. Sean can reflash them (smokeysevin). I'm not aware of any issue with the 2006s--I have a 2005 I rebuilt going on...
  9. Replies
    20
    Views
    1,629

    Not sure about Iowa, but in Texas that year will...

    Not sure about Iowa, but in Texas that year will go for $3500 - $4000 on a single trailer. I just sold a 2009 for $3700 on a single last week. I'm thinking a fair price for a clean pair on a double...
  10. Replies
    12
    Views
    3,507

    See this thread for troubleshooting:...

    See this thread for troubleshooting:
    http://www.greenhulk.net/forums/showthread.php?t=186939

    -Greg
  11. Replies
    8
    Views
    2,425

    ^^^^ Listen to this guy. He knows what he is...

    ^^^^ Listen to this guy. He knows what he is talking about.
  12. Replies
    11
    Views
    1,869

    Stay away from Honda's--been discontinued for a...

    Stay away from Honda's--been discontinued for a while now. Look at the Yamaha non-supercharged MR1 skis--VX110 or other VX series. There's a reason most rental companies use VX110s--they are ultra...
  13. Maybe a cable through the tie down on the front...

    Maybe a cable through the tie down on the front or rear of the ski? Thieves would need to be pretty motivated. I also think a cover is good for prying eyes that want to lift the hatch to look for...
  14. Replies
    35
    Views
    4,765

    I had a chance to see the new models at the...

    I had a chance to see the new models at the Houston boat show recently, and was impressed with the amount of forward storage. Really nice. However, the location of the filler nozzle puzzles me--could...
  15. Looks like the organizer has a few pay trip's...

    Looks like the organizer has a few pay trip's planned for this summer:

    http://www.dangerouswateradventures.com/2018-adventures.html

    -Greg
  16. I agree with all the comments here. They were...

    I agree with all the comments here. They were really unprepared in the first two seasons, and made lots of rookie mistakes. I'm also surprised they did not put in keel guards, and bring many more...
  17. These videos are making me seasick.

    These videos are making me seasick.
  18. Yes, I have done this and the o-ring has a hard...

    Yes, I have done this and the o-ring has a hard time going back in. I've cut the o-ring to get it back in properly, and then use some RTV where the two ends meet.

    -Greg
  19. Replies
    23
    Views
    15,281

    Over time Yamaha will address the issues with the...

    Over time Yamaha will address the issues with the TR-1. None of the problems I've seen indicate anything mechanical, aside from the pump bearings wearing out at 300 hrs. I imagine it'll take a few...
  20. Replies
    14
    Views
    1,403

    Wow. Any pics?

    Wow. Any pics?
  21. Replies
    6
    Views
    2,284

    Keep in mind you're not lubricating the bearing...

    Keep in mind you're not lubricating the bearing as the bearing itself is hermetically sealed. Grease just helps keep out any water that might seep past the outer seals.

    -Greg
  22. Replies
    8
    Views
    1,112

    I hear you. I am so paranoid now on my Kawi's...

    I hear you. I am so paranoid now on my Kawi's that I've almost sunk on two occasions due to split hoses. I need to put in a bilge pump. The 15F has 9 cooling hoses to the Yamaha VX110s 3 hoses.
    ...
  23. Replies
    97
    Views
    7,084

    Yes. Agreed. Run it hard for at least 30 min....

    Yes. Agreed. Run it hard for at least 30 min. While running the siphon should pull any water leaking into the hull.

    I'm wondering, though, how water got into the motor in the first place. You...
  24. Replies
    97
    Views
    7,084

    Simple: They start every time and we don't worry...

    Simple: They start every time and we don't worry about blowing motors, oil lines falling off, rebuilding carbs, fouled plugs, etc, etc. By contrast, the MR-1 motor in the VX is one of the most...
  25. Replies
    97
    Views
    7,084

    Good compression numbers. Now that you've...

    Good compression numbers.

    Now that you've separated the pump out like that, it's going to be near impossible to get the driveshaft off. Like I said earlier, the splines are rusted where they meet...
Results 1 to 25 of 67
Page 1 of 3 1 2 3