Search

Type: Posts; User: K447

Page 1 of 8 1 2 3 4

Search: Search took 3.31 seconds.

  1. Thread: 95 Polaris SL 750

    by K447
    Replies
    2
    Views
    47

    Welcome. Click here, start reading....

    Welcome.

    Click here, start reading.
    http://polarispwcknowledge.shorturl.com/first-things-to-do

    Three oil filters?
  2. Replies
    5
    Views
    81

    What happened to the original CDI for that...

    What happened to the original CDI for that machine?
  3. Replies
    7
    Views
    80

    You cannot use a multi-meter to do continuity or...

    You cannot use a multi-meter to do continuity or ohm testing on a powered circuit.

    If there is no DC battery voltage at the described MFI connector pins then check for a fuse or circuit breaker...
  4. Replies
    7
    Views
    80

    Are the pins being inserted into the correct...

    Are the pins being inserted into the correct locations?

    Do you have battery voltage between the black and red/purple (fused battery voltage) wires at the connector?
  5. I added the Worx trim arm extension to increase...

    I added the Worx trim arm extension to increase trim nozzle angle range.

    I also installed the extended Deanís steering nozzle, which increases both steering input response but also trim effect.
    ...
  6. Glad to hear you have the machine back in your...

    Glad to hear you have the machine back in your hands.

    The electrical box should have a large rubber o-ring going around the entire perimeter of the seam. There should be a groove for it. If that...
  7. Replies
    7
    Views
    80

    Welcome. The wires that are disconnected in...

    Welcome.

    The wires that are disconnected in the photo include black wire which is electrical ground for the MFI dash display. The black wire needs to be re-inserted into the correct socket in the...
  8. Replies
    6
    Views
    138

    Welcome. Where are you located? Click on My...

    Welcome.

    Where are you located?

    Click on My Profile in top right corner of web site, update your location info. Sometimes someone nearby may be able to after help.

    I am not an expert...
  9. Thread: Hood shock

    by K447
    Replies
    6
    Views
    255

    I do not have nor work on Seadoo so I cannot...

    I do not have nor work on Seadoo so I cannot answer the how-to question directly.

    I will say that your gender should not have any influence on how others treat you on here. I certainly have no...
  10. Replies
    5
    Views
    81

    Welcome. Two or three cylinder red...

    Welcome.

    Two or three cylinder red carburetor engine?

    Any of the Gen III red engine CDI can be reprogrammed to match the ignition curve needed for your engine. One of the members on here has...
  11. Replies
    1
    Views
    62

    Using a digital multi-meter, what is the measured...

    Using a digital multi-meter, what is the measured DC voltage at the battery terminals when the engine is running?

    Does it change much as the engine is revved to circa 4000RPM?

    While the engine...
  12. Click the link below, look for the Virage...

    Click the link below, look for the Virage section.

    In there, find the info on 'binding reverse lever'

    http://polarispwcknowledge.shorturl.com/first-things-to-do
  13. Replies
    2
    Views
    186

    My understanding is there is no CANDooPro GPS...

    My understanding is there is no CANDooPro GPS speedometer module for the 2019-2020 FX with the color LCD digital screen dash. There is no OEM speed sensor at all, the dash estimates speed using...
  14. Thread: RIDE help please

    by K447
    Replies
    9
    Views
    225

    SCU is the RiDE system.

    SCU is the RiDE system.
  15. Thread: RIDE help please

    by K447
    Replies
    9
    Views
    225

    The left side RiDE lever is a throttle for the...

    The left side RiDE lever is a throttle for the engine, indirectly. The left lever sends a signal to the RiDE motor+control unit in the rear of the hull. The RiDE unit then signals the engine ECU to...
  16. Perhaps when Yamaha began using NanoXcel hull...

    Perhaps when Yamaha began using NanoXcel hull material?
    NanoXcel hulls first appeared in 2008

    NanoXcel.shorturl.com
  17. Thread: RIDE help please

    by K447
    Replies
    9
    Views
    225

    Find the large white square electrical connector...

    Find the large white square electrical connector for the RiDE motor cable. Near the lower left corner (left side as when standing behind the hull) of electrical panel area, the RiDE multi-wire cable...
  18. Replies
    3
    Views
    78

    Welcome. Where are you located? Tip: Click...

    Welcome.

    Where are you located?

    Tip: Click My Profile in top right corner of web site, update your location info. Helps others know whether you are nearby.


    This link will provide some...
  19. http://polarispwcknowledge.shorturl.com/first-thin...

    http://polarispwcknowledge.shorturl.com/first-things-to-do
  20. Welcome. Click here, start reading :) ...

    Welcome.

    Click here, start reading :)

    http://polarispwcknowledge.shorturl.com/first-things-to-do
  21. Thread: RIDE help please

    by K447
    Replies
    9
    Views
    225

    Is this high revving in reverse happening in the...

    Is this high revving in reverse happening in the water or on the trailer?

    Does the reverse bucket lower when you squeeze the RiDE lever?

    Does it shift properly between forward, neutral and...
  22. Replies
    16
    Views
    358

    Short trailers tend to get sideways easily while...

    Short trailers tend to get sideways easily while reversing, compared to a longer trailer.

    A trailer that is too light on the tow ball (not enough tongue weight) can sometimes become a handling...
  23. Replies
    16
    Views
    358

    Yep. ...

    Yep.

    http://greenhulk.net/forums/attachment.php?attachmentid=127009&d=1240190997

    First, use the right sized trailer for the watercraft.
    Adjust the trailer to fit the hull and have the correct...
  24. The electrical box shell is metal. It is...

    The electrical box shell is metal. It is connected to engine ground via that thin black wire to the stator. The positive post on the battery has full battery voltage.

    If the positive battery post...
  25. Replies
    5
    Views
    175

    That is true for the TDC beginning of the power...

    That is true for the TDC beginning of the power stroke.

    Is it also true for TDC on the exhaust/intake overlap stroke?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4