Search

Type: Posts; User: bmxjoe

Page 1 of 8 1 2 3 4

Search: Search took 0.31 seconds.

  1. Replies
    2
    Views
    261

    CP piston cylinder wall clearance

    What would be an ideal piston to cylinder wall clearance for a CP piston in a SVHO with a 19 lb wheel and a 9000 Rpm tune?
  2. Replies
    2
    Views
    262

    WTB - Parts WTB - fizzle F1000 intercooler.

    Looking for a clean freshwater fizzle F1000 that passes a pressure check.
  3. Replies
    2
    Views
    299

    Modified 2004 block

    I previously modified a 2004 block to build and drop into a 2012 RXT. I torqued the head on last night but I dont recall if I had previously removed the oil restrictor in the block or not. I need to...
  4. Replies
    18
    Views
    1,236

    Brian from where? Do you have his contact info?

    Brian from where? Do you have his contact info?
  5. Replies
    23
    Views
    868

    From my experience that lip will cause tolerance...

    From my experience that lip will cause tolerance issue's with the main bearing as well and "cleaning it up" will not help. The block will need to be remachined or replaced. Let me know if you find...
  6. Replies
    23
    Views
    868

    Most thrust bearing damage is caused from a...

    Most thrust bearing damage is caused from a failed pump that has pushed the driveshaft into the crankshaft. This will damage the thrust bearing but will also damage the cases. Even after installing...
  7. Replies
    2
    Views
    244

    No cluster lights

    Check for power and ground at the cluster before you assume the gauge is bad.
  8. Replies
    4
    Views
    597

    Yea I'm pretty sure that's not gonna be necessary...

    Yea I'm pretty sure that's not gonna be necessary unless your running a block guard, since the holes do not line up correctly.
  9. Replies
    4
    Views
    597

    If the 300 head gasket works without modification...

    If the 300 head gasket works without modification on a stock 215-260 block then I would assume its safe to say that there would be no issues running the complete 300 head?!
  10. What's the point of a thermostat if the cooling...

    What's the point of a thermostat if the cooling ports in the gasket are controlling operating temp?
  11. Replies
    4
    Views
    597

    300 HP head/ gasket on a 215HP?

    Is the 300 HP head compatible with the older block? Are the valves in the 300 compatible with the old head? Can the 300HP head gasket but used on the older head/block assembly? Just wondering what...
  12. Thread: 2004 rxp tune

    by bmxjoe
    Replies
    0
    Views
    314

    2004 rxp tune

    I have a built 2004 rxp engine that is running on the limiter and runs great with factory tune. I have heard that the older skis can be a bit tricky to get tuned right. And I have no trust in a...
  13. Thread: SVHO Milky oil

    by bmxjoe
    Replies
    19
    Views
    2,124

    When the oil cooler fails on these units it...

    When the oil cooler fails on these units it doesnt mix water with oil. It pushes oil overboard. You'll notice an oil slick around you at idle in the water.
  14. Replies
    4
    Views
    2,158

    Just a heads up that your part numbers are wrong...

    Just a heads up that your part numbers are wrong for the change of the cams from 2012 to 2013 it was 6S5-12171-00-00 in 2012 and changed to 6S5-12171-10-00 in 2013.
  15. Replies
    3
    Views
    489

    Differances between ACE 230 AND 300 ENGINE

    I have noticed that the crank, rod and piston are different for the 230hp engine as opposed to the 300 HP.
    I can understand the piston being different and maybe the rod to help bring cost down by...
  16. It will happen again! Next time just tap main...

    It will happen again! Next time just tap main relay with something. Bam like new!
  17. Replies
    6
    Views
    666

    I got that 2012 260hp speedster 150 intake grate...

    I got that 2012 260hp speedster 150 intake grate in and was able to modify it to work with my 05 215 hp Sportster. So it does work if anyone else is having this issue.
  18. Replies
    6
    Views
    666

    Well i ordered a intake grate for the 2012 260 hp...

    Well i ordered a intake grate for the 2012 260 hp speedster 150 part number ends in 1852 where as the 08 'tx ends in 1851 hopefully i got it right. Theres not alot of information out here on these...
  19. Replies
    8
    Views
    210

    :smt100

    :smt100
  20. Replies
    6
    Views
    666

    bump

    bump
  21. Replies
    8
    Views
    210

    Sweet baby jesus someone help me.

    Bump
  22. Replies
    8
    Views
    210

    The OEM part numbers are different

    The OEM part numbers are different
  23. Replies
    8
    Views
    210

    There is not. And the OEM part is no longer...

    There is not. And the OEM part is no longer available.
  24. Replies
    34
    Views
    13,817

    we need answers people. Somebody with connections...

    we need answers people. Somebody with connections make a phone call.
  25. Replies
    8
    Views
    210

    bumpity bump bump

    bumpity bump bump
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4