Search

Type: Posts; User: TMiller

Page 1 of 8 1 2 3 4

Search: Search took 1.18 seconds.

  1. Replies
    10
    Views
    154

    Where did you get the fittings that go in the...

    Where did you get the fittings that go in the head for the pisser kit? The I.D. on those have to be same as the stock ones
  2. Replies
    4
    Views
    94

    Especially in heavy chop with a full tank of fuel...

    Especially in heavy chop with a full tank of fuel 15f feels nose heavy at low speeds.
  3. Did you confirm the tank is leaking ?

    Did you confirm the tank is leaking ?
  4. Assuming youre in the water? Can you post a video?

    Assuming youre in the water? Can you post a video?
  5. Pipe is discontinued. Most used pipes will have...

    Pipe is discontinued. Most used pipes will have some corrosion but yours looks pretty bad hard to tell by pics. Is it just that one hole or a few of them? Could try to keep an eye out for a clean...
  6. Replies
    7
    Views
    354

    Did you check the cam journals ? The bits of...

    Did you check the cam journals ? The bits of bearings/aluminum usually end up making a new home there.
  7. Replies
    4
    Views
    229

    Poll: Generally if you run your fingernail across the...

    Generally if you run your fingernail across the defect and you can feel it then it needs to be corrected. The individual jounals should also be measured for consistency and compared to the specs in...
  8. Start with a compression test on all 3 cylinders....

    Start with a compression test on all 3 cylinders. Wouldnt hurt to pull the the jet pump and inspect especially if it has over 50 hours on it or the history is unknown.
  9. Replies
    29
    Views
    1,895

    Myself, I didnt care for the one piece head. If...

    Myself, I didnt care for the one piece head. If the cylinders are not all exactly the same height one would think that would create an issue. If you are looking for something brand new I guess the...
  10. Replies
    29
    Views
    1,895

    I measured the chamber on a 36cc head directly...

    I measured the chamber on a 36cc head directly next to the spark plug hole and shows about 5/8 of an inch (0.65). It is not a very precise measurement but you get the idea. These have a beefy o-ring...
  11. Replies
    29
    Views
    1,895

    That is interesting that the piston was hitting...

    That is interesting that the piston was hitting on the inner edge there. The angle on the head should be greater that the angle on the crown of the piston so the outer edge should hit first.
    Like...
  12. Replies
    29
    Views
    1,895

    I can’t remember for sure but I think gaskets are...

    I can’t remember for sure but I think gaskets are 0.010 thick so you would need 3. Again I can’t remember for sure but I think squish on the red heads are 0.055 if you add 3 head gaskets then you are...
  13. Replies
    29
    Views
    1,895

    I saw you pulled one head. Did it have an o-ring?...

    I saw you pulled one head. Did it have an o-ring? I will measure the 2 different heads tonight if I have time.
  14. Replies
    29
    Views
    1,895

    I read through your original post too quickly. I...

    I read through your original post too quickly. I didn’t realize you yourself never did a compression test. That’s where I would start so you know what you have and not trust what someone else told...
  15. Replies
    29
    Views
    1,895

    I have a complete set of R&D 36cc red heads brand...

    I have a complete set of R&D 36cc red heads brand new in package if you need a replacement. The interchangeable domes were always easier if you wanted to switch back and forth from pump gas to race...
  16. Replies
    6
    Views
    534

    FS Here is a link to ADA racing for replacement...

    Here is a link to ADA racing for replacement domes. https://adaracing.com/personal-watercraft-products/pwc-domes/dome-kawasaki-ultra-150-1200-stxr-billet-head/
  17. Replies
    29
    Views
    1,895

    I see you have one of the heads off. Post a pic...

    I see you have one of the heads off. Post a pic of the chamber on like a 45 deg angle I can probably tell you if they are 42 or 36
  18. Replies
    29
    Views
    1,895

    I have a set of skiworx billet heads with...

    I have a set of skiworx billet heads with interchangeable domes for sale. PM me if interested.
  19. Replies
    29
    Views
    1,895

    As you said the6 come in 42cc or 36cc. With stock...

    As you said the6 come in 42cc or 36cc. With stock pistons 42cc should around 145psi and 36cc should be around 180psi. Now groupk also modified these heads to use on their level 2 kits with modified...
  20. Replies
    1
    Views
    287

    You should post this up on PWCtoday in the...

    You should post this up on PWCtoday in the general section. Someone over there may know. http://www.pwctoday.com/forumdisplay.php?f=11
  21. Reverse bucket ? Maybe try to find someone with...

    Reverse bucket ? Maybe try to find someone with a 300 in your area so you can swap complete pump and test.
  22. Thread: 2012 stx15f

    by TMiller
    Replies
    7
    Views
    525

    See if this helps ...

    See if this helps http://greenhulk.net/forums/showthread.php?t=282377
  23. Replies
    9
    Views
    819

    180 psi must have been a typo. The original post...

    180 psi must have been a typo. The original post says the other 2 cylinders are at 130 and looks like a stock head in the background.
  24. Replies
    9
    Views
    819

    Whoops.....

    Whoops.....
  25. Replies
    9
    Views
    819

    Ring probably moved once the pin was gone. ...

    Ring probably moved once the pin was gone.

    May be fuel system related. How old is the fuel? You could put the heads back on and pressure test the motor to rule out air an air leak.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4