Search

Type: Posts; User: smokeysevin

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    7
    Views
    353

    FS - Parts Nope, sorry. Sean

    Nope, sorry.

    Sean
  2. Replies
    17
    Views
    975

    Start by adding a shim/washer between the hull...

    Start by adding a shim/washer between the hull mounts and the plate at the rear to adjust the angle of the plate.

    I ground the mounts for the plate down so the front of the plate was flush or...
  3. Replies
    17
    Views
    975

    Thanks, I am reasonably happy with how they...

    Thanks, I am reasonably happy with how they turned out. A couple notes on them, make sure you round any edges on them, bashing your shin on a sharp piece of aluminum under the water line sucks ass. ...
  4. Replies
    17
    Views
    975

    What is your goal for the tabs? Sean

    What is your goal for the tabs?

    Sean
  5. Replies
    17
    Views
    975

    Yep, mine is all doo, I mostly meant to look for...

    Yep, mine is all doo, I mostly meant to look for where I have mine mounted and attached.

    Sean
  6. Replies
    17
    Views
    975

    Take a look at my kawidoo thread, there are (or...

    Take a look at my kawidoo thread, there are (or should be) some pictures of the vts install.

    Sean
  7. Replies
    17
    Views
    975

    easiest method would be to use a yamaha quick...

    easiest method would be to use a yamaha quick trim setup or set it up as an auto drop.

    Sean
  8. Ok cool, its been a while since I played with the...

    Ok cool, its been a while since I played with the stock setup. My megasquirt primes on key-on so I wasn't 100% sure. On my 12f, I used to just bump the starter button and let the pump prime if I had...
  9. Its been a while since I ran the stock ecu but if...

    Its been a while since I ran the stock ecu but if my memory is right, the fuel pump only kicks on when you hit the starter button for a few seconds.

    Sean
  10. Replies
    7
    Views
    353

    FS - Parts Triple Fuel Pickup Sold Sean

    Triple Fuel Pickup Sold

    Sean
  11. Replies
    14
    Views
    722

    Yeahhhhh we can't see anything from the pictures....

    Yeahhhhh we can't see anything from the pictures.


    What jet pump are you running? It may be producing a more rapid engine decel when the pump loads back up.

    Sean
  12. No need to apologize, we all gain when people...

    No need to apologize, we all gain when people share their experience.

    Sean
  13. Wax did a limited run so they may or may not be...

    Wax did a limited run so they may or may not be any left.

    My only complaint with the bed plate is that the clearance on the motor mounts is a little tight but that could be due to the rhaas...
  14. Replies
    3
    Views
    197

    The only aftermarket tunes that I know of that...

    The only aftermarket tunes that I know of that riva did for the stx were race gas only.

    One set was for the supercharges motors, and one set was for the high compression motors.

    Sean
  15. Replies
    3
    Views
    197

    I think the immobilizers are different, the cam...

    I think the immobilizers are different, the cam position nub is in a different spot relative to the crank angle on the early vs later models. The temp sensor curves are also different early vs late...
  16. Much appreciated, the camera hides most of the...

    Much appreciated, the camera hides most of the flaws but I keep telling myself that its a 33 year old standup, its okay for it not to be perfect. I am hoping to get some more work done on the hull...
  17. Replies
    6
    Views
    258

    The fuel system likes to corrode and take out the...

    The fuel system likes to corrode and take out the injectors, check for rust in the tank and plan on replacing the pump, filter, and reg. Budget for spark plugs, and fuel injector cleaning. The iac...
  18. Replies
    5
    Views
    259

    The riva kits ran the vortech blowers off the...

    The riva kits ran the vortech blowers off the crank coupler and were bolted to the motor. I would bet with a 1-2mm spacer you could run 5-7psi. Just a guess though and you would want to be...
  19. Replies
    5
    Views
    259

    The biggest issue you will face with doing the...

    The biggest issue you will face with doing the charger there is driveline flex hucking the belt off. I considered a system like that for a while but didn't feel confident that the play in the motor...
  20. Not being familiar with ti retainers, why do they...

    Not being familiar with ti retainers, why do they need to be replaced so frequently?

    Sean
  21. Replies
    5
    Views
    176

    Yep, learned it the hard way all in the name of...

    Yep, learned it the hard way all in the name of testing. Riva mod is fine if you follow the directions exactly.

    Sean
  22. Replies
    7
    Views
    353

    FS - Parts Crank and Gaskets Sold Sean

    Crank and Gaskets Sold

    Sean
  23. Replies
    23
    Views
    807

    That leads me to believe that the ecu isn't...

    That leads me to believe that the ecu isn't losing timing or sync which indicates either a fault in the wiring, or a fault in the ecu.

    Since you have tried an alternate ecu it makes me think...
  24. Replies
    5
    Views
    176

    DO NOT RUN A STRAIGHT PIPE the engine will suck...

    DO NOT RUN A STRAIGHT PIPE the engine will suck water up the manifold and hydro lock the motor.

    Sean
  25. Replies
    23
    Views
    807

    When 2/3 spark is it a consistent...

    When 2/3 spark is it a consistent pattern/interval or does it seem random?

    Sean
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4