Search

Page 1 of 5 1 2 3 4

Search: Search took 1.00 seconds.

  1. Replies
    22
    Views
    744

    To me it looks like the center plug is lean and...

    To me it looks like the center plug is lean and already trying to destroy your new rebuild. The clean one on the right is either flooding so badly that it's washing the plug clean, OR maybe not...
  2. Replies
    22
    Views
    744

    The white plug is way too lean. You MUST richen...

    The white plug is way too lean. You MUST richen it or you'll burn up that cylinder very quickly.

    I really don't like the gray plug. That cylinder may be having a meltdown. Gray deposits often...
  3. Replies
    9
    Views
    175

    So the only suspect components between the...

    So the only suspect components between the battery (+) and the hot side of the lanyard switch (red wire), is the main fuse (30A) and the wire harness connector for the left hand control's lanyard...
  4. Replies
    15
    Views
    915

    2-Stroke I put the water temp sensor on and was able to...

    I put the water temp sensor on and was able to get the alarm off but still was not getting power or a click. Jumped the starter solenoid with a screwdriver and I got the starter to bump. Replaced...
  5. Replies
    5
    Views
    321

    1200: Yes, prime the oil lines. No need to run...

    1200:
    Yes, prime the oil lines. No need to run premix initially unless doing a full top end rebuild and even then it's not necessary.
    Tygon works fine everywhere.
    Consider doing the Oside Bill...
  6. Replies
    17
    Views
    1,108

    View Post

    I feel like Iím learning all over again. After a long hiatus I had no idea of all the additional maintenance required. Especially on 2strokes. ThAnkful for these forums and thankful for YouTube
  7. Replies
    11
    Views
    422

    I'm w Jonesy, needle arm height should be flush w...

    I'm w Jonesy, needle arm height should be flush w body of carb, check it w a razor blade.
    Your pop off is low for stock jetting as well or high if using the Oside recipe?
  8. Replies
    19
    Views
    740

    View Post

    I depend on these forums so much itís not even funny! Definitely frustrating when there no conclusion or resolution!
  9. Replies
    1
    Views
    130

    Lesson in chasing a problem

    I have 2 GP1200Rís and an XLT1200 that I bought with a damaged engine. They all have the same engines and carbs , I am very experienced with this format yet I chased an imaginary ďelectrical ď...
  10. Replies
    5
    Views
    247

    you'll need the spline holder tool to lock up the...

    you'll need the spline holder tool to lock up the assembly in a vise ( show at how to link above)

    That's not a stock prop as far as I can tell, might be an impros, which uses an internal wrench
    ...
  11. Replies
    5
    Views
    233

    Yes, that will make a very large different, less...

    Yes, that will make a very large different, less restriction into the engine. But that "ductwork" is a flame arrestor designed to stop sparks from coming out of the intake if something goes wrong....
  12. Replies
    19
    Views
    740

    Might want to add clunks to pickup lines while in...

    Might want to add clunks to pickup lines while in there.
  13. Replies
    7
    Views
    360

    WTB Thanks for the heads up, yes I did. I ended...

    Thanks for the heads up, yes I did.

    I ended up finding a Riva Rideplate and YF CF 19/19 prop used on ebay, so now only looking for:
    -Reed Petals (prefer carbon)
    -Milled or Aftermarket Head...
  14. Replies
    15
    Views
    915

    2-Stroke I was considering getting one from them. Ended up...

    I was considering getting one from them. Ended up purchasing a good case and new wsm cylinder and 3 pistons. I got all the gaskets, seals, powervalves and carb kits. The only thing I need is the...
  15. Replies
    4
    Views
    260

    Looks like the screen to your power washer...

    Looks like the screen to your power washer [emoji23]
  16. Replies
    56
    Views
    3,030

    Swiss cheese the air box w 1" spade bit, remove...

    Swiss cheese the air box w 1" spade bit, remove all front tubing, keep metal screen, no need for a cone filter, and you can run the Oside recipe all day. Ran that for yrs w no issues.
  17. Replies
    11
    Views
    1,133

    FS - Parts i got a couple last week, same message, easy to...

    i got a couple last week, same message, easy to spot.
  18. Replies
    11
    Views
    1,133

    FS - Parts Not allowing a user to send PMs until a certain...

    Not allowing a user to send PMs until a certain post count is reached would make it harder for them. The pm scams Ive been sent were from users with 0 post count.
  19. Replies
    11
    Views
    1,133

    FS - Parts Guys when you get these PM’s please report them...

    Guys when you get these PM’s please report them so we can ban these scammers
  20. Soo good to be back on the water after lock down!

    It was soo good to finally get a day out on the water after all this covid lockdown business, there were some good fish around too

    https://www.youtube.com/watch?v=sonNkShplMM
  21. Replies
    7
    Views
    360

    WTB GP1200R Stage 2 Parts

    Looking for parts for a 2000 GP1200R 66v Powervalve build:
    -3 ProX Pistons
    -Reed Petals (prefer carbon)
    -Milled or Aftermarket Head
    -Flame Arrestors / Adapters
    -Riva Ride Plate
    -Pump Seal Kit...
  22. Replies
    17
    Views
    702

    View Post

    Yes. Waveeater clips. Thanks Iíll open them tonight
  23. Replies
    17
    Views
    702

    Power valve clips

    I recently got my old go1200r back in the water. I CANNOT remember if I added the PV clips. Would be as easy as removing one of the PV covers to check? Would they be visible if present ?
  24. Thread: Fs yf cd 13-20

    by WFO
    Replies
    13
    Views
    531

    FS - Parts this is a concord for a gpr/xlt. 13/20 is steep,...

    this is a concord for a gpr/xlt. 13/20 is steep, so repitched would work for xlt or gpr 1200

    you need a dynafly 14/20 for your 06 gpr
  25. Replies
    3
    Views
    196

    Thank you guys for reply. Yeah glad to be back on...

    Thank you guys for reply. Yeah glad to be back on water. Iíve owned this ski since 2003. Had it in storage for years. Recently had carbs rebuilt. I feel like Iím learning all over again. Great...
Results 1 to 25 of 116
Page 1 of 5 1 2 3 4