Search

Type: Posts; User: Bible Fan

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    6
    Views
    982

    I removed the stator. Everything looks good. ...

    I removed the stator. Everything looks good. Going to order a new cdi and coil
  2. Replies
    6
    Views
    982

    I have tried everything. Only issue I can find...

    I have tried everything. Only issue I can find is Ohm reading on CDI orange wire stays at infinity; the book says it should move and then go back to infinity. Also the ohms are a little high on the...
  3. Porting, timing, and ignition... Does this mean...

    Porting, timing, and ignition... Does this mean that the big pipe stays in? Just do the cc delete with the D plate?
  4. Replies
    20
    Views
    3,382

    My 3up TRIXX shipped last week. Waiting for it...

    My 3up TRIXX shipped last week. Waiting for it to be delivered this week to my New Jersey dealership.
  5. Swapping MPEMs and e-boxes and electronics Sea Doo to Jetski to Tiger Shark to Wvrnnr

    Hello Gentlemen,

    How do I find info on swapping electronics from one brand to another? I have seen the Jetski Brothers do this.

    Thanks,

    Peter
    Annapolis MD area
  6. Replies
    3
    Views
    758

    I don't understand how to make a GPR exhaust fit....

    I don't understand how to make a GPR exhaust fit. I want to know because I'd like to get rid of the HUGE exhaust in my GP1200R. It seams to only be HUGE IOT accommodate the cat converter
  7. Replies
    6
    Views
    982

    None of the ohm readings for reg/rec, CDI, and...

    None of the ohm readings for reg/rec, CDI, and the coil match the table in the manual. I ordered a new multimeter today.
  8. Make my 96 XP and 97 XP perform like a Spark Trixx

    Thinking about drilling a new hole in my VTS nozzle horn IOT allow the VTS motor arm to add several degrees up and down. I'm not sure if the motor will burn up due decreased mechanical advantage. ...
  9. Sea Doo Spark Trixx vs 1996 XP and 1997 XP

    Just got access to a brand new Trixx. I also have a 96 XP and a 97 XP.

    Wheelie mode is really fun.

    It has amazing low end. Still breaking it in.

    After a 180 spin out both XPs boil...
  10. Options for 1200XLT Exhaust Replacement GP1200R gpr xlt

    Gentlemen,

    I don't want to put that huge heavy black U expansion chamber or the silver muffler back in. What options are out there? It looks like everything is large in order to deal with the...
  11. Replies
    6
    Views
    982

    1995 Waverunner III no spark

    Hello,

    My 95 WR3 has no spark. Just bought it. Seller said it abruptly quit while running on a garden hose. I pulled a known good cdi out of my 93, installed it and still no spark. Ohms were...
  12. Replies
    10
    Views
    463

    K447, You are the man. Thanks for the info. ...

    K447, You are the man. Thanks for the info.

    Should I mess with a Genesis at all? I like it for family riding; very comfortable and fast. Good for tubing. Maybe I'll just wait for a nice, stock...
  13. Replies
    10
    Views
    463

    What motor would you put in a Genesis hull? Non...

    What motor would you put in a Genesis hull? Non power valve Yamaha 1200 with a milled head?
  14. Replies
    10
    Views
    463

    The stock engine is a 1200 with 135 hp. The 787...

    The stock engine is a 1200 with 135 hp. The 787 makes 110 hp. I really liked my old genesis. I’ll be watching for a motor
  15. Replies
    10
    Views
    463

    Frankenstein Genesis

    I have access to a free Genesis hull. How tough is it to drop in a Sea Doo 787 running premix?
  16. Replies
    3
    Views
    280

    20 psi for four days. No change. $60 on EBay.

    20 psi for four days. No change. $60 on EBay.
  17. Replies
    3
    Views
    280

    97 XP stiff steering cable

    Gentlemen, I have disconnected the cable at both ends and the issue is the cable. I have hooked up 30 psi pressure to a tube filled with WD-40 and have managed to get about an ounce or two into the...
  18. Replies
    2
    Views
    953

    Starter Rear bolt stuck 97 GTX

    Hello gang,

    trying to remove 97 GTX starter to swap into my 97 XP. Front two bolts are out. Rear bolt will not accept a 6mm alan. 5.5 is too small. Pics show something inside head of bolt.
  19. Replies
    15
    Views
    2,828

    What is the Seal Unit? I am sorry, do you mean...

    What is the Seal Unit? I am sorry, do you mean the seal on the shaft? I replaced that on mine. I also had to replace the 7.5 amp fuse (was getting the single click when trying to run the VTS.) I...
  20. Replies
    348
    Views
    109,432

    Sticky: 02 Genesis I 54 speedo, 6720 RPM (Nicest ski...

    02 Genesis I 54 speedo, 6720 RPM (Nicest ski ever made IMHO)
  21. Replies
    23
    Views
    9,877

    Where did you buy the seal kit and grate?

    Where did you buy the seal kit and grate?
  22. Replies
    3
    Views
    1,544

    Tried to remove the carbs tonight. Stripped the...

    Tried to remove the carbs tonight. Stripped the top forward bolt. It was easy to remove from the engine, but it spins the carb when trying to loosen. Only about a turn or two to go and it stripped...
  23. Replies
    20
    Views
    1,741

    No, it was just a few mm forward or aft. I don't...

    No, it was just a few mm forward or aft. I don't know. Not the extension you are talking about.
  24. Replies
    20
    Views
    1,741

    I don't know the dimensions of it, but the ski...

    I don't know the dimensions of it, but the ski had a bunch more low end and could pull a skier up on two skis.
  25. Replies
    20
    Views
    1,741

    4th of July, Chesapeake bay, super low tide, best...

    4th of July, Chesapeake bay, super low tide, best friend ran it aground. Wouldn't even pull a tube on plane. major gouges on SS wear ring. Had a friend do a "summer fix" with a newer impeller and a...
Results 1 to 25 of 50
Page 1 of 2 1 2