Search

Type: Posts; User: Teufelhund

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    78
    Views
    8,077

    Just curious, if you think you don’t need to...

    Just curious, if you think you don’t need to remove the pump, does that mean you are not installing the pro cooling kit? Seems impossible to install without pump out… Ofc you don’t need the pro...
  2. Replies
    3
    Views
    150

    Yeah I haven’t logged total consumption but I...

    Yeah I haven’t logged total consumption but I also was averaging about 5-5.5 mpg from dash computer, I reset before each ride to follow tank to make sure I’m not actually on empty
  3. So I have the same basic mods as tucker…except...

    So I have the same basic mods as tucker…except haven’t done ribbon delete yet. I have gen 2 riva ride plate + intake grate. I never ran my stock ride plate on my stage 1+ so I can’t compare. Using...
  4. Replies
    78
    Views
    8,077

    View Post

    the coupler I refer to is the factory 90į coming off the hull is replaced with a very short straight piece by Worx. The hose then goes from water box to that new “coupler”. The tach I have now is the...
  5. Replies
    78
    Views
    8,077

    I left water box stock, added worx free flow...

    I left water box stock, added worx free flow going out factory hole in hull, only changed the coupler. I didn’t notice much top end speed, perhaps a tiny bit of extra pull…my prop is too tall, I...
  6. Replies
    78
    Views
    8,077

    Just rode tonight after adding a Worx free flow...

    Just rode tonight after adding a Worx free flow exhaust to my setup…gotta say, I’m not a big fan, fairly annoying drone thru 2500-5000 rpm, gotta be going near 45 before it subsides. My first...
  7. There’s a locking lever, you slide it and the...

    There’s a locking lever, you slide it and the socket will start to release
  8. Maptuner

    This one
  9. Lol, of course..that will be my next problem in...

    Lol, of course..that will be my next problem in my journey to stage 2, maptuner won’t work :facepalm:
  10. Replies
    78
    Views
    8,077

    K447, u are absolutely one of the best sources of...

    K447, u are absolutely one of the best sources of info here in the forums, with a wealth of knowledge just overwhelming at times. I agree in principle on what your saying, but the reality of exposed...
  11. Replies
    78
    Views
    8,077

    Dual battery vid

    Hereís a link to my description of my wiringÖlol, keep in mind Iíve no aspirations to be a YouTube star, hence my poor vid skills

    https://youtu.be/2NvalvG7w-A
  12. Replies
    78
    Views
    8,077

    Wiring schematic

    Hereís my wiring setup. Lol, donít judge my drafting skills, itís only one cup of coffee so far :)
  13. Replies
    78
    Views
    8,077

    https://youtu.be/JCHxkcBTUZ0 This video shows the...

    https://youtu.be/JCHxkcBTUZ0 This video shows the set of aluminum bars machined by Michael, and the extra battery box. I only bought the partial kit, and made my own wire. The battery is a deka...
  14. View Post

    FYI, A 1Ļ⁄₁₆ socket is approximately .01mm off the 27 mm size of the hex on the impeller, so virtually indistinguishable…
  15. FYI, I did actually remember this question...

    FYI, I did actually remember this question yesterday and intentionally left my screen on fuel page, it automatically switched to speedo page when I go into forward drive…
  16. 1 1/16” deep well, cut off drive end with cutoff...

    1 1/16” deep well, cut off drive end with cutoff wheel.
  17. Tool

    Tool I made and use the setup K447 shows with a breaker bar under my trucks wheel, and cheater pipe on impeller endÖcame off like butter
  18. Is that 5200 fast cure?? I thought that was too...

    Is that 5200 fast cure?? I thought that was too “much” for a pump, 4200 or Right Stuff was the choice to use?
  19. Pretty sure my 2021 gp does this, I was checking...

    Pretty sure my 2021 gp does this, I was checking fuel used and never switched back, and it was on Home Screen…but I’m going off memory and not an actual conscience test..I’ll try next time I’m out.
  20. Replies
    3
    Views
    240

    Hmmm…so, u only are monitoring on spot check type...

    Hmmm…so, u only are monitoring on spot check type of setup? It does seem a LOT of guys have longevity issues with the sensors, I was just trying to find out if there’s a way around them failing...
  21. Replies
    3
    Views
    240

    AFR monitoring setups

    So, come winter and once Iím out of the water for the end of this season, Iím set to upgrade to Stage 2 on my 2021 gp 1800. In anticipation of my just knowing Iíll wanna go further, Iím thinking to...
  22. lol, if you get your bucking issue resolved I...

    lol, if you get your bucking issue resolved I might be interested in seeing that mod list, if I get bored with Stage 2 I may wanna go more…next years project perhaps
  23. Bucking

    Hereís mine from intake end and outlet endÖnot sure I can tell itís any different
  24. I’ll try to snap a pic in the morning

    I’ll try to snap a pic in the morning
  25. My 13/20 really needed to ge repitched down to...

    My 13/20 really needed to ge repitched down to like 13/19 or 13/18…I’m just waiting on backordered stuff to do it all at once for stage 2. Lol, since you said you saw this at 70, I’m not as worried...
Results 1 to 25 of 142
Page 1 of 6 1 2 3 4