Search

Type: Posts; User: TJS0712F

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    198

    Going to the new three bearing set up requires a...

    Going to the new three bearing set up requires a new pump housing assembly(+2011 up), shaft, retaining nut, and cone set up as well as the bearings and seals that go with it. There are several posts...
  2. Replies
    49
    Views
    1,592

    For the gauge issue. This is normal junk kawi...

    For the gauge issue. This is normal junk kawi gauge. This is a huge issue. Stock replacements fail too. They allow water intrusion. Smokeyseven has a post on this. People say to ground the...
  3. Replies
    5
    Views
    308

    You can cut out the old wear ring, buy on from a...

    You can cut out the old wear ring, buy on from a company in in fla for 70 bucks on ebay. I have a whole write up on this I did years ago on here. Not that hard.
    ...
  4. 07 12F

    07 12F
  5. 40 Hrs. Puked bearings almost trashed my housing...

    40 Hrs. Puked bearings almost trashed my housing (saved it). Total garbage design in all aspects. I have several posts on this.
    T.J.
  6. I know I can weld a turned fitting back on that...

    I know I can weld a turned fitting back on that thing, or even an NPT bung on there. However it all has to come apart. Might just be worth it to find another one.
  7. Replies
    38
    Views
    3,473

    Great story Pete. I remember the blackout. Being...

    Great story Pete. I remember the blackout. Being from Ct. I am only 60 min from the City. Yes people around here refer to it as "the City"
  8. Replies
    4
    Views
    389

    FS - Parts How about a gauge/meter set up that works. If so,...

    How about a gauge/meter set up that works. If so, how many hours.
  9. Replies
    7
    Views
    709

    Not sure what you buddy is saying it is the axle....

    Not sure what you buddy is saying it is the axle. What is his diagnosis of this. How does he know it is the axle. Having built trailer axles from scratch I would like to hear what he has to say.
  10. Replies
    29
    Views
    1,749

    That never worked for me. I have a 2007 12F. Has...

    That never worked for me. I have a 2007 12F. Has been in slo mode all season. I tried that. SDW. Maybe cause the gauge is totally shot.
  11. Replies
    81
    Views
    3,821

    Sean, Does that threaded coupler you are...

    Sean,
    Does that threaded coupler you are thinking of have to have reverse threads on one side of it. Not sure which way the crank spins on those when standing behind it.
  12. Replies
    81
    Views
    3,821

    You forgot my channel LOL: TJS Welding and...

    You forgot my channel LOL: TJS Welding and Fabrication
  13. Replies
    81
    Views
    3,821

    I see single point internal and external...

    I see single point internal and external threading in your future. One of the best machinists I have seen and he is down south is Abom79. That is his YT channel. I know he can do this. He is in Fla....
  14. Replies
    81
    Views
    3,821

    I have welded different size shafts together...

    I have welded different size shafts together utilizing a custom machined collar if you will. I TIG plug weld them first on the lathe while continually checking runout and using the heat to move to...
  15. Replies
    81
    Views
    3,821

    Forgive me I am a little slow. So you are running...

    Forgive me I am a little slow. So you are running the seadoo pump and 15F engine correct. How are you going to mate these two. Are you going to use the seadoo shaft and turn down the Kawi side and...
  16. Looks like a cool project Sean. You ever need...

    Looks like a cool project Sean. You ever need some alum Tigged or something CNC plasma cut let me know. I have a full shop at my house.
  17. Ya Steve, please do add a build thread when you...

    Ya Steve, please do add a build thread when you do this. Also if you need something small/ship-able CNC plasma cut for your project let me know. I have a 4 x 8 table in my garage/shop that I built...
  18. Good luck with your endeavor. Lack of info here...

    Good luck with your endeavor. Lack of info here will result in garbage in garbage out. Just keep throwing parts at it. You'll get it.
  19. What is the speed after he worked in it. If he...

    What is the speed after he worked in it. If he checked it what are the clearances between the wear ring and the impeller.
    And what is a "stack".
  20. Never understood why people rev the piss out of...

    Never understood why people rev the piss out of these things out of the water(no load).
    Do you red line your car in neutral.
    How many hours.
    Are you the original owner.
    Does your gauge work....
  21. Replies
    3
    Views
    220

    IG. I can't even get IG to open on my phone after...

    IG. I can't even get IG to open on my phone after they did an update last week. Junk.
  22. Replies
    37
    Views
    967

    I see you found the post I was referring to. Hope...

    I see you found the post I was referring to. Hope this helps you. Please keep us posted.
  23. Replies
    21
    Views
    807

    Typical Kawasaki pump seals go bad water...

    Typical Kawasaki pump seals go bad water ingesting destroying bearings scenario. I fixed by pump when this happened. Welded up the impeller edges and machined down to get a .008" clearance. I have an...
  24. Replies
    37
    Views
    967

    Makes no sense. This is you asking for help, not...

    Makes no sense. This is you asking for help, not a how too.
  25. Replies
    37
    Views
    967

    I just noticed this is in the FAQ and How To...

    I just noticed this is in the FAQ and How To section. Think it should be moved to the Kawi 4 stroke section. It might get more input.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4