Search

Type: Posts; User: HDAV

Page 1 of 8 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    12
    Views
    471

    If chain is centred on the gears, later design is...

    If chain is centred on the gears, later design is 5 links wide not 3 like the original, (may need wider guides) why would it move? That’s surely only as likely as the thinner chain falling off the...
  2. Replies
    10
    Views
    444

    New longer wider hull.........

    New longer wider hull.........
  3. hopefully not but compression test is the answer,...

    hopefully not but compression test is the answer, make sure the oil level is correct. I would be more concerned about corrosion in side the motor with such low hours..... average of 4 per year is a...
  4. Replies
    2
    Views
    94

    Hmmm oil on the anode that’s a new one......

    Hmmm oil on the anode that’s a new one......
  5. Replies
    9
    Views
    457

    I use the middle one..... easy to keep in ski and...

    I use the middle one..... easy to keep in ski and mostly plastic so won’t rust too fast.....

    https://www.harborfreight.com/Line-Clamp-Set-3-Pc-63596.html
  6. Replies
    4
    Views
    148

    Compression test..........

    Compression test..........
  7. Replies
    9
    Views
    457

    Clamp off the cooling water line from pump to X...

    Clamp off the cooling water line from pump to X where flush port connects.... make sure revere bucket is raised! As no water can get into the cooling system you can tow as fast as you wish.....

    ...
  8. Replies
    6
    Views
    286

    Jeeeezzzz you guys care more about the look of...

    Jeeeezzzz you guys care more about the look of the engine bay than how they ride...... yeah knock a bit off for it being crusty.... don’t buy waverunner to save money... ride em hard enjoy them sell...
  9. Replies
    6
    Views
    286

    2016 is a solid year, hours are low were they...

    2016 is a solid year, hours are low were they serviced each year as per manual? Used in salt water or fresh? Any outward signs of corrosion damage? Any corrosion tot he ride plate or pump? Do they...
  10. Thread: Water in intake

    by HDAV
    Replies
    3
    Views
    99

    So someone opened the plugs while it was sitting?

    So someone opened the plugs while it was sitting?
  11. Thread: Water in intake

    by HDAV
    Replies
    3
    Views
    99

    Do you know why it sank? Shop vac as much water...

    Do you know why it sank? Shop vac as much water out as you, can is oil clean?

    You may need to pull the J pipe off and dry it and intercooler if you have an intercooler full of water.........
    ...
  12. Replies
    12
    Views
    286

    Yeah but never seen a white hull turned black...

    Yeah but never seen a white hull turned black during a ride! That’s not normal surely.......

    i should have taken a picture picture but the whole rear of ski was black
  13. Replies
    12
    Views
    286

    Then why the soot? The oil is yamalube 2T I...

    Then why the soot? The oil is yamalube 2T I think....how do you adjust the pump?
  14. Replies
    12
    Views
    286

    That is fine if a you want to run premix and b...

    That is fine if a you want to run premix and b the issue is the pump over oiling.......
  15. Replies
    4
    Views
    235

    http://greenhulk.net/forums/attachment.php?attachm...

    http://greenhulk.net/forums/attachment.php?attachmentid=454118&stc=1Google the service manual its out there for a 2008 sho same motor...my advice change the sensor.....
  16. Replacing rear gunwhale trims removing old rivets

    So I need to replace the rear gunwhale trims on my fx......do I just drill them out or do I need to do something else? Also is a special tool
    needed to fit them or will a basic hand riveter work?
  17. Thread: Water in hull

    by HDAV
    Replies
    9
    Views
    477

    Thanks only wish I had a local hardware store...

    Thanks only wish I had a local hardware store that carried that kind of stuff.....
  18. Replies
    14
    Views
    819

    Fingers crossed you find a good motor...

    Fingers crossed you find a good motor...
  19. different style but I keep one of these rolled...

    different style but I keep one of these rolled up for exactly these occasions takes seconds to throw on and saves the leather getting wet and salty.....
    ...
  20. Replies
    12
    Views
    286

    Still oil injected yes and max oil flow would...

    Still oil injected yes and max oil flow would explain why it runs fine at WOt but won’t idle and is really sooty (not normal) and happens after a recent ride

    Is it the cable 66E-26320-00-00 PUMP...
  21. Thread: Water in Oil

    by HDAV
    Replies
    21
    Views
    474

    It’s either 1: water in oil from bung...

    It’s either

    1: water in oil from bung issue.....(hope that’s what it is)

    2: failed oil cooler.....(possible)

    3: cracked head........(my $2)
  22. Replies
    12
    Views
    286

    XLT800 soot around pump

    Asking for a friend who has an 04 XLT 800 and after a recent ride there was a lot of black soot and grime around the pump. Ski rides ok but very dark around the pump looks almost black......

    whats...
  23. Replies
    4
    Views
    264

    Fill in service book....that what a mechanic...

    Fill in service book....that what a mechanic would do....recommend keeping invoice for oil and filter and personally use Yamaha branded ones despite warranty ending before I bought the ski......
  24. Replies
    14
    Views
    819

    Wow con rod did a 180 and punched a hole in the...

    Wow con rod did a 180 and punched a hole in the oil pan? Or something int he hull nicked a hole in oil pan? Heard of the later happening when tools are left in hull... found anything lying under the...
  25. Replies
    2
    Views
    114

    not the 2007 but I do have one for an mr-1 ski ...

    not the 2007 but I do have one for an mr-1 ski

    F1S-28197-1G-11
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4