Search

Type: Posts; User: beerdart

Page 1 of 8 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    1
    Views
    104

    JetRenu Stankaway

    JetRenu Stankaway
  2. Replies
    34
    Views
    9,327

    Yep

    Yep
  3. Replies
    34
    Views
    9,327

    Good times.

    Good times.
  4. Replies
    64
    Views
    1,444

    I like where your headed with the doo pump. Here...

    I like where your headed with the doo pump. Here is my Doo pump for the Polaris MSX anything is possible. Water flow from the doo pump should be fine as its restricted with a...
  5. Replies
    64
    Views
    1,444

    Just make a new through hull bearing mount that...

    Just make a new through hull bearing mount that is larger to accept the larger shaft combo. That is what I did on my MSXDOO after repeatedly breaking the Polaris shafts.
  6. Replies
    18
    Views
    591

    Love it. Make sure your alignment is spot on with...

    Love it. Make sure your alignment is spot on with that setup there is no way it should break drive shafts.
  7. Replies
    49
    Views
    3,310

    Damm 13

    Damm 13
  8. Replies
    19
    Views
    414

    VIN number only matters for Maptuner and Candoo....

    VIN number only matters for Maptuner and Candoo. You can marry any VIN to the cluster I put my Polaris VIN in for my conversion.
  9. BUDS reads angle not % so if your idle angle is...

    BUDS reads angle not % so if your idle angle is 7-8 then WOT should be 90-7-8 or 82-83.
  10. Replies
    79
    Views
    4,651

    Yes they should work fine.

    Yes they should work fine.
  11. Replies
    79
    Views
    4,651

    Yes one nut at a time no need to pull the head....

    Yes one nut at a time no need to pull the head. McMaster has the washers and o-rings.
  12. Replies
    79
    Views
    4,651

    Ive use copper crush washers as well as the...

    Ive use copper crush washers as well as the bonded ones with good results.
  13. Replies
    3
    Views
    229

    Its a reed switch and not repairable unless you...

    Its a reed switch and not repairable unless you replace the reed switch.
  14. Replies
    79
    Views
    4,651

    Long time no talk good to see your still around.

    Long time no talk good to see your still around.
  15. Replies
    21
    Views
    965

    Yes depending on how F-up the repair was.

    Yes depending on how F-up the repair was.
  16. Replies
    21
    Views
    965

    http://greenhulk.net/forums/showthread.php?t=16972...

    http://greenhulk.net/forums/showthread.php?t=169727
  17. Replies
    21
    Views
    965

    The splines of the beerdart/addicted shaft is...

    The splines of the beerdart/addicted shaft is stock yamaha Part #2 in the pic unscrews and is threaded onto a cut and threaded seadoo shaft. I have the...
  18. Replies
    21
    Views
    965

    Shaft info....

    Shaft info.
    http://greenhulk.net/forums/showthread.php?t=93416


    http://greenhulk.net/forums/showthread.php?t=42454
  19. Replies
    12
    Views
    451

    I think its a JOBE and not Jettribe. ...

    I think its a JOBE and not Jettribe.

    https://www.promo-jetski.com/en/pilot-equipment/75589-jobe-ruthless-side-entry-nylon-life-vest-8718181240307.html

    ...
  20. Replies
    1
    Views
    239

    WTB - Parts I have one with 8800 rev limit flashed by...

    I have one with 8800 rev limit flashed by greenhulk and pink injectors.
  21. Replies
    4
    Views
    339

    ...........................

    ...........................
  22. Where is the main battery ground hooked up to?

    Where is the main battery ground hooked up to?
  23. Thread: 785 PROject

    by beerdart
    Replies
    265
    Views
    21,332

    https://www.marcorubber.com/o-ring-groove-design-f...

    https://www.marcorubber.com/o-ring-groove-design-face-seal.htm

    http://www.sealanddesign.com/page/o-ring-groove-design-metric
  24. Thread: 785 PROject

    by beerdart
    Replies
    265
    Views
    21,332

    .044 is huge and your o-ring will not last....

    .044 is huge and your o-ring will not last. Sounds like you have an american o-ring in a metric grove. What are the o-ring grove dimensions? width and depth?
  25. Thread: 785 PROject

    by beerdart
    Replies
    265
    Views
    21,332

    The o-ring should not be .010 high the squish...

    The o-ring should not be .010 high the squish should be the same with or without o-ring.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4