Search

Type: Posts; User: Kosh

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Possibly all clear by now, it wouldn't of hurt to...

    Possibly all clear by now, it wouldn't of hurt to flush soak it in petrol prior but too late now.
    If it was an exchange or new engine generally to keep warranty you would be required to fit a new...
  2. Me too, no mention about cleaning out or...

    Me too, no mention about cleaning out or replacing the oil cooler?
  3. Replies
    3
    Views
    212

    Both inner terminals are fuel sender connections....

    Both inner terminals are fuel sender connections. Outside ones are fuel pump. One of them is 12v positive, hot all the time, the other is negative switched by the ECU.

    Try powering up the pump...
  4. Replies
    9
    Views
    568

    Wipe the inside of the rubber hose with acetone...

    Wipe the inside of the rubber hose with acetone or similar also outside wher the clamp sits, wipe down where your putting it on as well.
    Cant be anything else but contamination, unless your running...
  5. Replies
    6
    Views
    1,034

    This was on an 05 there was a 4 pin (if I...

    This was on an 05 there was a 4 pin (if I remember correctly) connector that teed of some can wiring for depth sensor.
    Point is that moisture upset the system enough to cycle the system as you...
  6. Replies
    6
    Views
    1,034

    I had this a deade ago, was water intrusion in...

    I had this a deade ago, was water intrusion in the can connector block, unplug and check nothing has gone green.
  7. Replies
    2
    Views
    314

    Confirm fuel pressure under load is 58 psi

    Confirm fuel pressure under load is 58 psi
  8. Replies
    0
    Views
    198

    Heated Handgrip wiring

    double up
  9. Replies
    0
    Views
    201

    Heated Handgrip wiring

    Hi Guys,
    Any one help with pin identificatin on the accessory heated handgrips please? I'm aware that there are extra harnesses available depending on model year.
    There are 3 pins on the plug,...
  10. Thread: Dashpac o2 sensor

    by Kosh
    Replies
    6
    Views
    564

    Check all pins are locked in, I have one from new...

    Check all pins are locked in, I have one from new that the lock failed possibly at assembly? Just glued it in place. This was on the O2 socket.
  11. Replies
    4
    Views
    359

    Make sure your battery voltage is maintaing 12v...

    Make sure your battery voltage is maintaing 12v while cranking?
  12. Replies
    10
    Views
    888

    I have used WSM in past with success, now use the...

    I have used WSM in past with success, now use the 300 gasket on the 1503 blocks.
  13. Thread: 4-tec powered MSX

    by Kosh
    Replies
    949
    Views
    86,009

    Recent pics

    Not much has changed over the years, removed pump wedge, smaller Venturi, lifters in the foot well ( so used to then in the RXPX I had to have them) 10 different intakes to the supercharger! Like...
  14. Thread: 4-tec powered MSX

    by Kosh
    Replies
    949
    Views
    86,009

    Still have mine, has not been in the water for...

    Still have mine, has not been in the water for the last two seasons but it's ready to go!
  15. The 2019 Gtx manual I looked at earlier in the...

    The 2019 Gtx manual I looked at earlier in the week had the jet pump cone removed at 100 hours to check for water intrusion, not until 200 hours did it say to remove, grease splines, inspect for...
  16. Replies
    7
    Views
    1,568

    My guess would be it would work ok water cooling...

    My guess would be it would work ok water cooling wise, concern is the clearance allowing for the movement of the motor on the engine mounts, you will need X ?clearance to ensure it will not rub into ...
  17. Replies
    9
    Views
    862

    Learner key?

    Learner key?
  18. Replies
    5
    Views
    431

    I don't believe any more was done other than what...

    I don't believe any more was done other than what I wrote at the time, other than prop adjustments it's never been back apart, oil has been changed a few times, comes out as clean as it went in....
  19. Replies
    5
    Views
    431

    Well proves never rely on my memory! Had look on...

    Well proves never rely on my memory! Had look on my old thread and found the info you may be looking for, start at post 86
    http://greenhulk.net/forums/showthread.php?t=139727&page=9
  20. Replies
    5
    Views
    431

    I have the same set up on my conversion, oil...

    I have the same set up on my conversion, oil bathed and very reliable. Going back 10 years I needed to replace the seal collar and used a 2005 part but needed to machine it as it was a touch longer...
  21. Replies
    33
    Views
    4,191

    A very knowelable contributor throughout the...

    A very knowelable contributor throughout the years, he will be missed.
  22. Replies
    39
    Views
    6,357

    There is an oil pressure operated vent valve on...

    There is an oil pressure operated vent valve on top of your oil tank, hard to see it failing. Check it out.
  23. Replies
    9
    Views
    1,295

    Great information, would seem this is a possible...

    Great information, would seem this is a possible upgrade for most high power 1500cc versions.
  24. Replies
    4
    Views
    995

    They can be made to fit but require modifications...

    They can be made to fit but require modifications as the bolt spacing is different. There was a thread about it, do a search.
  25. Check out www.inoveli.com/store for a different...

    Check out www.inoveli.com/store for a different take on throttle actuation.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4