Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.04 seconds; generated 49 minute(s) ago.

  1. I think so too. I've done oil changes on 20 and...

    I think so too. I've done oil changes on 20 and 30 hour machines that still had that much.
  2. Replies
    3
    Views
    87

    WTB - Parts Yep....it's a unicorn. I've got one here taken...

    Yep....it's a unicorn. I've got one here taken apart with stator in great shape, no internal bearing area issues. I will take $150 shipped in the cont. US.
  3. Replies
    2
    Views
    100

    Thanks bro.

    Thanks bro.
  4. Replies
    8
    Views
    507

    I'll probably just haul all mine to scrap this...

    I'll probably just haul all mine to scrap this winter. At least I'll get a few bucks.
  5. Replies
    2
    Views
    100

    GP1200r GP1300r cylinder temps

    Can anybody tell me the typical temps of a triple GPR after warmed up and idling? I know it depends on the water temp but I'm seeing about 10-12 degrees warmer on the front cylinder. I know that's...
  6. Replies
    2
    Views
    158

    Sure sounds like a head gasket.....I guess you'll...

    Sure sounds like a head gasket.....I guess you'll have to pull it to find out. I just did one on a 300x and couldn't find anything as to why it happened. New gasket and running good.
  7. Replies
    1
    Views
    106

    Check with Westside Powersports. They've been...

    Check with Westside Powersports. They've been parting out Seadoos for years.
  8. Replies
    1
    Views
    333

    I recently cut one open in an attempt to repair...

    I recently cut one open in an attempt to repair it. The reason nobody is offering repair on that style gauge is because the polarizer film that gets sunburnt is on the BACK side of the glass! That...
  9. Replies
    1
    Views
    139

    You should NOT hear bubbling when blowing into...

    You should NOT hear bubbling when blowing into the return line. The return dumps out freely into the top of the baffle. The tank would have to be filled up to the neck to hear bubbling! Check the...
  10. Replies
    3
    Views
    142

    Threebond if the surfaces are scratched or pitted...

    Threebond if the surfaces are scratched or pitted up. Otherwise clean surfaces with new gaskets require nothing, just assemble dry. If you just want extra insurance the copper spray is great.
  11. Thread: 255 rebuild

    by Myself
    Replies
    4
    Views
    310

    Yep,.....the service manual. Everything is in it...

    Yep,.....the service manual. Everything is in it and pretty well written. Any hangups or things you don't understand can be asked on the forum and somebody will have an answer. All I can think of...
  12. Replies
    1
    Views
    111

    Ohm the primary side (where the connector hooks...

    Ohm the primary side (where the connector hooks up), should be low ohms, like around 1-1.5 ohms.
    Ohm the secondary (what touches the spark plug). One lead there and one to either side of the...
  13. Replies
    4
    Views
    270

    Sometimes an ECU goes bad. The last one I sent...

    Sometimes an ECU goes bad. The last one I sent for repair was keeping one injector open and flooding a cylinder. If it's actually doing this it will hydrolock. Black plugs are just very rich not...
  14. Replies
    17
    Views
    698

    Sorry, yes. Basically just step back and watch...

    Sorry, yes. Basically just step back and watch for pink instead of clear in the general area under the pump. A bit will spit out of the exhaust, a bit will spit out of the pissers, and of course from...
  15. Replies
    7
    Views
    359

    What?!! You must ride like a grandma lol!

    What?!! You must ride like a grandma lol!
  16. Replies
    17
    Views
    698

    I also use the flush ports. I have a garden hose...

    I also use the flush ports. I have a garden hose fitting clamped to a 2ft length of hose. Screws right into a 'Doo and Kawi, and into the adapter on a Yamaha. On the Yamaha I also use a pair of hose...
  17. LOL! I was going to say the exact same thing....

    LOL! I was going to say the exact same thing. 2009 or newer with a non supercharged 1.8L. I'd go for the Cruiser with the hip support seating but don't let it be a deal breaker cause you can always...
  18. Replies
    4
    Views
    270

    Most likely throttle cable mis-adjusted and TPS...

    Most likely throttle cable mis-adjusted and TPS giving the ECU signal to enrich the mixture. Check that there is slack in the cable and that all the hoses to the IAC motor are hooked up.
  19. Replies
    7
    Views
    359

    I mean......I know it's the time of year for...

    I mean......I know it's the time of year for everything pumpkin spice but COME ON!!!

    The electrode does not show much wear and I also don't see much (if any) carbon buildup. Guessing less than 15...
  20. Replies
    17
    Views
    698

    Here's how I do them. Have you seen pics of what...

    Here's how I do them.
    Have you seen pics of what moisture does to these Kawi pumps.....YIKES! Fill the tank with non ethanol.
    I use Lucas ethanol safegaurd to treat the fuel first.
    I use a 2psi...
  21. I'd run it. Bet it will do fine.

    I'd run it. Bet it will do fine.
  22. Replies
    4
    Views
    179

    Clean the PV passage and place a new valve down...

    Clean the PV passage and place a new valve down in it. Check to see that it's not protruding into the cylinder while in the closed position.
  23. Replies
    2
    Views
    153

    The easiest hull to mount it in will be...

    The easiest hull to mount it in will be Superjet.....any year.
  24. I have replaced several Kawi triple CDI's because...

    I have replaced several Kawi triple CDI's because of a no fire on one cylinder. I just tested out a 900STX this evening....no fire on front cylinder after only 2-3 minutes then misfiring badly on...
  25. Replies
    4
    Views
    179

    Normally, when I see that, the shoulder in the...

    Normally, when I see that, the shoulder in the cylinder is worn. It allows the valve to drop a bit lower than it should and kiss the piston. Of course.....it leads to a broken valve.
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4