Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    7
    Views
    165

    None of the things that I mentioned will throw a...

    None of the things that I mentioned will throw a code.
  2. Replies
    3
    Views
    76

    Yes, rebuild the carbs. Making it run good by...

    Yes, rebuild the carbs. Making it run good by cutting fuel supply suggests a needle/seat leakage. Extra fuel passing by that shouldn't be. Could also be diaphragms so loose that they're actually...
  3. I've used many wsm and sbt power valves with no...

    I've used many wsm and sbt power valves with no issues. The lever link captures the pin so no wave eater clips necessary.
  4. Replies
    3
    Views
    72

    You can directly power up the panel with a 12v...

    You can directly power up the panel with a 12v supply, the info is in the service manual. If it does not power up then it's faulty.
  5. Replies
    7
    Views
    165

    Part of rebuilding an RFi is replacing fuel...

    Part of rebuilding an RFi is replacing fuel filter and strainer in tank, cleaning and testing spray pattern of fuel injectors, testing fuel pressure, and zeroing out the tps. If somebody didn't do...
  6. Replies
    4
    Views
    95

    Spray penetrating lube around the edge then heat...

    Spray penetrating lube around the edge then heat it with a propane torch. Just follow the edge around for about 3 minutes. Then smack around the whole edge with a plastic hammer with a bit of tension...
  7. Replies
    11
    Views
    317

    Nice work! I know you'll get to it, but don't...

    Nice work! I know you'll get to it, but don't forget to rebuild the jet pump with the updated parts. I use te kit from KP Performance.
  8. Replies
    2
    Views
    132

    Hmmmm....I've been through thousands upon...

    Hmmmm....I've been through thousands upon thousands of parts this year alone and don't have that problem. Sounds like you need to switch suppliers.
  9. Replies
    3
    Views
    124

    Leaking intercooler? Spraying a bit of water only...

    Leaking intercooler? Spraying a bit of water only at high rpm?
  10. Replies
    3
    Views
    141

    I've always packed them with red tacky. Never had...

    I've always packed them with red tacky. Never had any issues.
  11. Thread: 1997 1100 stx

    by Myself
    Replies
    6
    Views
    161

    Yes. Maybe it's a 99.

    Yes. Maybe it's a 99.
  12. Thread: 1997 1100 stx

    by Myself
    Replies
    6
    Views
    161

    I have a customer with a '98 STX 1100 with 425...

    I have a customer with a '98 STX 1100 with 425 hours on it and has never been apart! I just put a cdi on it a couple weeks ago, compression still 115psi on all 3!!
  13. Not an '18 but I just had to fix a stator...

    Not an '18 but I just had to fix a stator connection on a '14 with 34 hours! The triangular statr plug was never fully seated from the factory. Outside looked good, inside the pins were burnt off!
  14. Replies
    3
    Views
    128

    Have you tried new spark plugs?

    Have you tried new spark plugs?
  15. Replies
    1
    Views
    81

    2-Stroke I use thus...

    I use thus stuff.....https://www.homedepot.com/p/PC-Products-PC-11-1-lb-Paste-Epoxy-160114/100649621
    It works great. After full cure spray some white appliance epoxy paint over it.
  16. Check with Westside Powersports. I believe they...

    Check with Westside Powersports. I believe they also keep new parts in stock. Jess is at Lake of the Ozarks and he can rush it if you want?
  17. Replies
    8
    Views
    236

    Did you try new spark plugs first?

    Did you try new spark plugs first?
  18. Replies
    0
    Views
    65

    Gp1300 rough idle and low top speed.

    I did the d-plate and chip, power valve keepers, and some other maintenance to this 1300 early this year. It seems the idle is too low and top speed was only in the low 50's. Plugs show a good color,...
  19. Replies
    11
    Views
    315

    Many skis do it at slower speeds. The early Kawi...

    Many skis do it at slower speeds. The early Kawi stx hull does it BAD just up on plane. The '97 and up Seadoo XP also does it pretty bad about 25-30 mph. You just get used to it.
  20. Replies
    6
    Views
    166

    You can throttle it on the trailer. Maybe it will...

    You can throttle it on the trailer. Maybe it will show up. Yes, the shaft is press fit into the bearing housing. No need to pull the pump. The driveshaft is just splined into the midshaft. Sometimes...
  21. Lots of options for boat tachs. Many have...

    Lots of options for boat tachs. Many have adjustable "pulse per rev" switch to work with many different engine configurations.
  22. Replies
    3
    Views
    172

    After degreasing and wire wheeling all threads, I...

    After degreasing and wire wheeling all threads, I use a drop of blue threadlocker on every bolt.
  23. Replies
    6
    Views
    166

    What???? Not on a '96 model, that's only 23 years...

    What???? Not on a '96 model, that's only 23 years old!!!! Lol!
  24. Replies
    10
    Views
    8,076

    I've done 2 951's this past week and have another...

    I've done 2 951's this past week and have another one sitting here to do. I amost never replace the fuel return line. Even when the green goo is everywhere on the supply side, the return is good. At...
  25. Replies
    11
    Views
    408

    Sounds like a no spark on one cylinder. There...

    Sounds like a no spark on one cylinder.
    There are a couple common issues I find on these old triples. First check all coils. You can ohm from the boot to ground (around 10k ohm) and ohm at the coil...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4