Search

Type: Posts; User: Myself

Page 1 of 8 1 2 3 4

Search: Search took 0.72 seconds.

  1. Replies
    10
    Views
    150

    Look at the spark plug.........new?........dead...

    Look at the spark plug.........new?........dead giveaway!
    Older........coloration?
  2. I've used Winderosa kits a hundred times, never...

    I've used Winderosa kits a hundred times, never had an issue. They probably do need kits based on age alone. Try turning all 3 low screws out an additional 1/4 turn. It should clear right up.
  3. Replies
    2
    Views
    56

    Put in a battery and check things out. 150-200...

    Put in a battery and check things out. 150-200 hours a 951 top end is worn slap out. If it's in that range, just pull it out for complete teardown and inspection. If......by some miracle.....it's ...
  4. Replies
    2
    Views
    62

    Thick grease where the starter goes into the...

    Thick grease where the starter goes into the engine. You can put a drop of blue threadlocker on the mounting bolts. Scrape the paint off the new starter where the ground cable mounts.
  5. Nevermind....got one coming!

    Nevermind....got one coming!
  6. Need 255 intercooler hose 273000254-->273000282 ASAP please

    Anybody have a brand new Seadoo intercooler inlet hose ready to ship out? Original part# 273000254 appears to be superceded by #2732000282. I'm about fed up with online dealers advertising how...
  7. Replies
    4
    Views
    93

    If the exhaust pipe was in the way, then you have...

    If the exhaust pipe was in the way, then you have an rfi. Pipe is on the opposite side on a carbed model.
  8. Thread: 1996 slt 700

    by Myself
    Replies
    3
    Views
    94

    Well, I see a Seadoo electrical box......maybe...

    Well, I see a Seadoo electrical box......maybe throw a Rotax into it!
  9. Replies
    4
    Views
    93

    You just have to feel for the bolts. Front 2 are...

    You just have to feel for the bolts. Front 2 are metric allen. Rear bracket has a 13mm going int the case. Then pull it up and take off the power wire.
  10. Thread: Driveshaft plug

    by Myself
    Replies
    21
    Views
    370

    No pessure on the carbon seal is usually either...

    No pessure on the carbon seal is usually either trashed jet pump bearings OR just a worn out bellows not pushing any more.
  11. Replies
    9
    Views
    399

    I'll throw in my bid of 72.

    I'll throw in my bid of 72.
  12. Thread: Driveshaft plug

    by Myself
    Replies
    21
    Views
    370

    That's a bumper. The shaft has fore and aft play....

    That's a bumper. The shaft has fore and aft play. The bumpers give cushion so you don't have metal to metal contact. Nothing to do with taking on water.
  13. Replies
    9
    Views
    194

    If it's premix then no need to worry about oil...

    If it's premix then no need to worry about oil lines.
    WaveEater is a name brand. Any updated pv links or clips will work...I use the cheapie clips off Ebay, they work fine. Couplers aren't necessary...
  14. Replies
    9
    Views
    194

    The jet pump noise is normal. Hard to tell in...

    The jet pump noise is normal. Hard to tell in that vid but engine sounds pretty normal to me. The pv 1200 does make a funny missing/popping/knocking type thing at idle. Wire out of the pipe is an...
  15. Replies
    4
    Views
    110

    My method has been to get everything good to go...

    My method has been to get everything good to go with motor mount bolts still a tad loose. Then with coils unhooked, crank it over a bit. The engine will settle in to straight alignment.
  16. Replies
    7
    Views
    141

    Does the stator and trigger ohm good? A sc...

    Does the stator and trigger ohm good? A sc failure can and will take out the stator if anything on the backside came loose.
  17. Replies
    3
    Views
    112

    Good stator or bad would not cause a total power...

    Good stator or bad would not cause a total power loss. Missing or loose grounds on the stator cover, or loose/corroded stator connector will disrupt power. Very possible it's that damn relay on the...
  18. Bearings are not directional......unless one side...

    Bearings are not directional......unless one side is open and one is sealed. I believe in your case they are double sealed meaning either side can face either direction.
  19. Replies
    8
    Views
    206

    I had a 155 blow a head gasket a few hours after...

    I had a 155 blow a head gasket a few hours after I replaced it........head was warped. Didn't catch it the first time.
  20. Sounds normal, especially if it has intake air...

    Sounds normal, especially if it has intake air mods. Those have a "roots" type blower, that's the way they sound.

    Do yourself a favor and update that jet pump ASAP.
  21. Replies
    4
    Views
    284

    Check your fuel pickup and switch. Sounds like it...

    Check your fuel pickup and switch. Sounds like it could be sucking air.
  22. Replies
    46
    Views
    745

    5200 by itself. I've done this repair a couple...

    5200 by itself. I've done this repair a couple times on the STX. Also just did something very similar on a 2017 Yamaha EX.
  23. Replies
    6
    Views
    267

    I installed an STXr gauge on this and it works...

    I installed an STXr gauge on this and it works just fine!
  24. Thread: STX-R Partout

    by Myself
    Replies
    17
    Views
    528

    FS - Parts A gauge I got from Sean, after a spit-n-shine....

    A gauge I got from Sean, after a spit-n-shine. Thanks bud.
  25. Replies
    5
    Views
    183

    1....cause it's a power valve 1200 2...cause...

    1....cause it's a power valve 1200
    2...cause there was no mention of replacing oil lines. The rear line on those usually pops first cause of shrinkage of the tubing. The longer the tubing, the more...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4