Search

Type: Posts; User: dalouie2

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thread: 2004 gp1300r.

    by dalouie2
    Replies
    3
    Views
    168

    2004 gp1300r.

    Hey hi all. Any help on this. Which lazer iridium ngk spark plug. ? For 2004 yamaha gp1300r thx d
  2. Replies
    4
    Views
    316

    silicone spray.

    John. I use. 656 marine. but leaves a film. and concerned about that. manual says. silicone sprays. so trying to determine the best thing to use.
  3. Replies
    4
    Views
    316

    Silicone spray

    HEY HI ALL , Do riders use. Yamaha brand silicone spray to coat the engine or. other brands? This is after riding and cleaning maintenance. Thx D
  4. Replies
    10
    Views
    950

    SO JUST ORDERED GALLON SALT AWAY AND A FLUSH...

    SO JUST ORDERED GALLON SALT AWAY AND A FLUSH ADAPTER. only been flushing with water. BEEN USING CRC 656. SPRAY ALL THE MOTOR METALS. ETC. BUT. AFTER 14 YRS SALT USE ON A 04. YAM...
  5. Replies
    10
    Views
    950

    Salt water prevenitives measures ?

    Is there any. And do any riders have a trick or two that work. To prevent the damage from salt water riding ?
  6. Replies
    3
    Views
    303

    geeez. not one reply ?

    geeez. not one reply ?
  7. Replies
    3
    Views
    303

    2004 Yamaha gp1300r. starter removal

    lol. This is the toughest thing to tackle removing the starter motor . anyone. have any ideas.? Cant get it to budge aft towards the rear of the ski. It will wobble up and down now after...
  8. Replies
    0
    Views
    180

    bilge pump for 04 Yamaha gp1300r.

    does anyone know which rule pump it is ? model #. thx d
  9. Replies
    1
    Views
    180

    07 gp1300r will not start

    recent non starting issue been doing this a bit as a delay when pushing starting button then would fire right up now will not start bilge runs, display lights up, new battery , ...
  10. Replies
    0
    Views
    138

    gp1300r engine warning display both skis

    hey hi , i have 2 gp1300r's 04 -07 both skis will flash engine warning in the displays yet i cant get a code from the display. i hold the reset alarm button or turn off the ski will ride on ...
  11. Popping the 3 amp fuse and any one hav a idea...

    Popping the 3 amp fuse and any one hav a idea as to fab a new screen when i get repair/replace im thinking a plastic something if i cant find stainless screen ????
  12. Having same issue here gp1300r blowing fuze ...

    Having same issue here gp1300r blowing fuze removed the stainless screen as it was all but full corroded /and or rust or other ... bench ran pump all good installed with out screen pre season ...
  13. o4 gr1300r exhaust temp warning audio and mutli display indicator

    Hey hi my ski sounds off after 10 min ride display and audio flashing hold a check code on display reads code 53 exhaust temp warning, so i shut of the ski wait to display clears start...
  14. Replies
    13
    Views
    1,729

    Mike is the man

    Mike thx for all your help i am good to go wow added the dud into the sensor cable and that solved the problem just coiled up the sensor at the muffler so BAM thank you for your...
  15. Replies
    13
    Views
    1,729

    hey hi mike i just read this, ill swap the chip...

    hey hi mike i just read this, ill swap the chip for the sensor . Get this i have two 1300r skis 04 --07 i took the exhaust sensor out of the o4 and installed into the o7 result was...
  16. Replies
    13
    Views
    1,729

    mike reading your reply the end of the exhaust ...

    mike reading your reply the end of the exhaust the sensor is the water temp sensor ... the ski displaying code exhaust temp sensor . code 53 thx d
  17. Replies
    13
    Views
    1,729

    Ok i was not on the correct sensor i checked...

    Ok i was not on the correct sensor i checked the cooling water temp sensor at the lowest point in the exhaust on item #15 the mixing joint so will remove the exhaust temp sensor and...
  18. Replies
    13
    Views
    1,729

    Mike to be clear i need to disassemble the...

    Mike to be clear i need to disassemble the lower exhaust area to check for sand obstruction ? Not just check the sensor itself thank you for all your tech suport as welll ill look at the...
  19. Replies
    13
    Views
    1,729

    Little more info on ski i did replace the cat...

    Little more info on ski i did replace the cat with a d ring plate but read i didnt need to put the dud chip in the sensor connection i do have the dud if needed but dont know if i do or...
  20. Replies
    13
    Views
    1,729

    Mike i removed the sensor was clean micro ...

    Mike i removed the sensor was clean micro scale at very top closest the the thread cleaned off very very minimal material took for test rub got the warning code 53 exhaust...
  21. Replies
    13
    Views
    1,729

    WELL READ SIMILAR POSTS,and will run the dash...

    WELL READ SIMILAR POSTS,and will run the dash test while warning is going off , then check for the code ,that may tell the problem . i hope
  22. Replies
    13
    Views
    1,729

    2007 gp1300r warning indicator

    Seems the engine temp sensor OR THE EXHAUST TEMP SENSOR ? is activating on a 40 min ride, then returned back to slip flushed with cool water ok cooled off ran dash test no code or code 01 ...
  23. thanks so much riders and readers sorry for...

    thanks so much riders and readers sorry for poor description, but u guys made it clear on solving my issue. thx again d
    forums like this one are so helpful . thumbs up big time.
  24. installed d plate temp warning still goes off

    after installing a d plate on my 2007 gp1300r and inserting the dud chip in wire harness temp audio warning activates ??? any help thx d
  25. Replies
    2
    Views
    1,750

    the sensor failed ?no need to deal with the cat...

    the sensor failed ?no need to deal with the cat convert ? thx d
Results 1 to 25 of 26
Page 1 of 2 1 2