Search

Type: Posts; User: ptscon

Page 1 of 8 1 2 3 4

Search: Search took 0.03 seconds; generated 34 minute(s) ago.

  1. Thread: Motec

    by ptscon
    Replies
    8
    Views
    404

    Why not simply go Vipec (LinkECU) if you want...

    Why not simply go Vipec (LinkECU) if you want stand alone, it doesn't have any license based restrictions and has a great support forum. Vipec is a re-badged Link ECU G4+ so anything that applies to...
  2. Thread: Motec

    by ptscon
    Replies
    8
    Views
    404

    That's a load of BS ...so you spend $3k+ on the...

    That's a load of BS ...so you spend $3k+ on the hardware and aren't allowed to tune for different fuels unless you pay up to get that "unlocked"?
  3. Stock 300 impeller vs SXX 13/16 RPM difference

    Hey guys, what kind of RPM difference is there between a stock 300 impeller and a solas 13/16.

    I want to try a pro re-worked stock impeller in my 260-Frankenstein thats spinning a 13/16 to 8800...
  4. Replies
    2
    Views
    113

    65mph @ 8700 RPM indicates a problem around the...

    65mph @ 8700 RPM indicates a problem around the jet pump area: bad wear ring, bad impeller

    Your impeller is spinning fast, not power problem, but not moving water to create thrust.

    Your setup...
  5. Replies
    0
    Views
    133

    FS - Parts Titanium Retainers

    Titanium Retainers

    They weigh 4.8 grams each, $180 shipped for the set, brand new.

    http://greenhulk.net/forums/attachment.php?attachmentid=457719&stc=1
  6. Replies
    0
    Views
    100

    FS Viton Valve Stem Seals

    A set of 12 brand new Viton valve stem seals.

    $60 shipped within North America.

    http://greenhulk.net/forums/attachment.php?attachmentid=457652&stc=1
  7. Replies
    6
    Views
    373

    Yes that's correct.

    Yes that's correct.
  8. Replies
    28
    Views
    1,889

    This is more funny than anything. Couple minutes...

    This is more funny than anything. Couple minutes with compressed air, shop vac and some wire will fix it up.

    I once bought a head advertised as from 2014 machine but when it got to me it turned...
  9. Replies
    22
    Views
    706

    Yes they can be really in there. My cheap valve...

    Yes they can be really in there. My cheap valve clamp tool actually bends sometimes getting the retainer to let go.

    Using rope with the piston at TDC will allow you to use more force vs just...
  10. Replies
    22
    Views
    706

    Skip the air, put a bunch of rope into the...

    Skip the air, put a bunch of rope into the cylinder through the spark plug hole, raise the piston to TDC and just let the valve rest on the rope on top of the piston.
  11. Replies
    6
    Views
    373

    I'm looking for pinout of the Maptuner X hdmi...

    I'm looking for pinout of the Maptuner X hdmi cable for seadoo. If anyone has it and feels like spending a few min to map the pins for me I would appreciate it :)
  12. Replies
    5
    Views
    393

    Your tune will have to be adjusted to account for...

    Your tune will have to be adjusted to account for more boost throughout the RPM range.

    I would not touch bearings on these chargers, chances are you'll do more harm than good by replacing them. ...
  13. Replies
    0
    Views
    127

    VTech vs Riva base maps

    Anyone know how VTech and Riva base maps compare for 4tec?

    I'm going back to flashing for this coming season and I'm locked to VTech system. "VT11 8900 174 36 33 Nor" is what I used couple...
  14. Replies
    3
    Views
    225

    The dude approves.

    The dude approves.
  15. Replies
    3
    Views
    225

    Oh boy, here we go :lol:

    Oh boy, here we go :lol:
  16. Replies
    6
    Views
    373

    I don't have buds but here's how the original...

    I don't have buds but here's how the original cable pins are mapped.

    Left side is the diagnostic port end (tuner cable end not actual port on the ski) and right side is RJ45 as looking at them...
  17. Replies
    5
    Views
    186

    WTB Oh I just want to frame one on my wall :D ...

    Oh I just want to frame one on my wall :D




    Want to let go of a single one?
  18. Replies
    5
    Views
    186

    WTB Looking for OEM 300 connecting rod 1

    Looking for a single 300/ACE connecting rod.
  19. That's pretty slick. Any way to use external...

    That's pretty slick.

    Any way to use external lambda input instead of the dashpac build in one?
  20. No it doesn't, 4tec blocks use regular iron...

    No it doesn't, 4tec blocks use regular iron sleeves.
  21. Thread: RIVA cam lift?

    by ptscon
    Replies
    4
    Views
    442

    RIVA cam lift?

    Just wondering if anyone measured lift on the riva cam?
  22. I wonder if Wiseco suggestion is a generic one...

    I wonder if Wiseco suggestion is a generic one for all their forged pistons or application specific. Jetski motors run at very high RPMs under boost for extended periods of time. It's not like a...
  23. A little crazy but cool :) You work/own at a...

    A little crazy but cool :)

    You work/own at a machine shop? Where did you source all the 300 charger internals?
  24. Not sure what CP calls for ring end gaps but...

    Not sure what CP calls for ring end gaps but those numbers look large, my current motor with Wiseco is 0.023 / 0.028.
  25. 17.5-ish If I were you I would not run less...

    17.5-ish

    If I were you I would not run less than 0.0035 and just round it up to 0.004 Running slightly looser will not cause any issues or performance loss. It will give the motor a bit more...
Results 1 to 25 of 188
Page 1 of 8 1 2 3 4