Search

Type: Posts; User: xlint89

Page 1 of 8 1 2 3 4

Search: Search took 0.13 seconds; generated 5 minute(s) ago.

  1. Replies
    6
    Views
    112

    Good advice ^^^^ Give those a shot and report...

    Good advice ^^^^

    Give those a shot and report back
  2. Replies
    5
    Views
    134

    Compression test? All 3 cyls firing?

    Compression test?

    All 3 cyls firing?
  3. Replies
    3
    Views
    91

    How about posting a clear picture of the elec...

    How about posting a clear picture of the elec box?

    Gray loom? Hmm.... Only thing I think of is the fuel sender wires, but those are pink and black.
  4. Replies
    3
    Views
    91

    I assume you have the lanyard installed? Is...

    I assume you have the lanyard installed?

    Is the engine plate ground good?

    How about the ground inside the elec box?

    Any corrosion on the terminal board inside the box?

    Have you eliminated...
  5. Replies
    9
    Views
    260

    They really are fun skis. Pretty light hull too....

    They really are fun skis. Pretty light hull too. The newer models switched from fiberglass to SMC and gained about 70-80 lbs. Funny thing is they seem to have cracking issues while the fiberglass...
  6. You are correct on both guesses. As for the...

    You are correct on both guesses.

    As for the steering cable, I cannot see it enough to tell if it runs the whole length of the engine. But yes, it runs over top of the mount at the rear.
  7. Sorry, didn't see this until now. I'll look...

    Sorry, didn't see this until now. I'll look tomorrow
  8. You remove the impeller and stub shaft from the...

    You remove the impeller and stub shaft from the jet pump. The alignment tool then slips into it's place.

    It's not a perfect system, but it gets you really close.
  9. Replies
    6
    Views
    98

    Sea Weed, plastic bag, or something in the pump...

    Sea Weed, plastic bag, or something in the pump possibly.

    You can also inspect the drive shaft splines on both ends for wear. Also look at the engine coupler for rubber shavings if you have that...
  10. Replies
    41
    Views
    1,270

    That's the filter combo. If that is the one you...

    That's the filter combo. If that is the one you have, you can eliminate the in line filter.
  11. http://greenhulk.net/forums/showthread.php?t=28334...

    http://greenhulk.net/forums/showthread.php?t=283343&highlight=pro+1200+driveshaft
  12. Please forgive the mess. Hope these help.

    Please forgive the mess. Hope these help.
  13. Replies
    9
    Views
    260

    50:1 oil ratio is pretty low. Most of us run 40:1...

    50:1 oil ratio is pretty low. Most of us run 40:1 Double check that the oil you're going to be using suggests 50:1. I'd hate to see you scorch the engine because you tried to save a few bucks on...
  14. Replies
    41
    Views
    1,270

    That's good you got the cover. Didn't see the...

    That's good you got the cover.

    Didn't see the water seperator. Is yours just the seperator, or do you have the filter/seperator?

    Reason I ask is I'm not a fan of the in-line filters. Plus it's...
  15. Replies
    4
    Views
    75

    780's should have the long pump and wear ring...

    780's should have the long pump and wear ring extension. And they are correct, the impeller is too big

    780 makes around 92 HP and the Virage 1200 makes about 135 HP
  16. Sorry, it's late and dark right now. I'll try to...

    Sorry, it's late and dark right now. I'll try to get you pics tomorrow
  17. Yep ^^^^ you got a ground issue. By touching...

    Yep ^^^^ you got a ground issue. By touching the aluminum elec box to the engine, you're completing the circuit.
  18. Replies
    41
    Views
    1,270

    Why is your hose coming of the fuel selector...

    Why is your hose coming of the fuel selector bending to the rear of the ski?

    Do you have the plastic cover between your battery and elec box? You'd better have one.
  19. Replies
    1
    Views
    124

    I've always installed it with the lip seal on the...

    I've always installed it with the lip seal on the inside and the smooth seal on the outside. (spring facing out)

    Make sure to pack some grease between the 2 seals to help keep air out too.

    I...
  20. Do you have a link to the stainless one? All i...

    Do you have a link to the stainless one? All i see is the aluminum for Polaris
  21. Replies
    41
    Views
    1,270

    Good idea. Hopefully it works out for you.

    Good idea. Hopefully it works out for you.
  22. Where did you find the SS wear ring? I like those...

    Where did you find the SS wear ring? I like those ones.
  23. Not sure how bad yours is, but for future...

    Not sure how bad yours is, but for future reference, you can have your impeller repaired and/or modified at places like Impros.

    The guys have been helping you out. You can use the Polaris 707 or...
  24. Replies
    41
    Views
    1,270

    Do the idle mixture screw adjustment with the ski...

    Do the idle mixture screw adjustment with the ski tied to the trailer or tied to something so it doesn't move when you adjust the screws. it will give you good accel and good idle with no plug...
  25. All Polaris impellers are SS just so you know. ...

    All Polaris impellers are SS just so you know.

    15/21 seems pretty small for a SLX 1200.

    Are you looking to gain more top speed or acceleration?
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4