Search

Page 1 of 15 1 2 3 4

Search: Search took 1.00 seconds.

  1. This is one part you want to buy new and OEM...

    This is one part you want to buy new and OEM ONLY!

    The older style stator has a 3 pin connector mid way in the harness to the regulator/recifier (RR). The 300 stator wiring runs directly to the RR.
  2. Replies
    15
    Views
    453

    that appears to be a pretty low quality...

    that appears to be a pretty low quality connection, I would resplice the wires, solder them and apply heat shrink tubing

    while the wiring is open, measure the a/c voltage output from the stator ....
  3. The drop in pressure tripping the alert when...

    The drop in pressure tripping the alert when going from cruise mode to WFO is a pretty good tell that when the regulator opens in the face of a sudden spike in pressure that it sticks while trying to...
  4. I'd be replacing the oil pressure regulator,...

    I'd be replacing the oil pressure regulator, since the parts changers have already guessed their way around the entire system at a large expense

    pro tip:

    if you ever encounter this kind of...
  5. Replies
    26
    Views
    3,721

    You post this a lot but its not true. I just...

    You post this a lot but its not true. I just took out my seal, unrelated, and it looks flawless after about 50-60 hours. This is the larger newer generation one. My previous one had 150+ hours...
  6. I'll be surprised if the stock ecu/HP tuners can...

    I'll be surprised if the stock ecu/HP tuners can handle 4 O2 sensors or 3 EGT probes and one O2 sensor, A/B maps, and/or electronic boost control!
  7. Replies
    33
    Views
    4,474

    Hi I work for a large company in technical...

    Hi I work for a large company in technical department investigating faults.
    We did an investigation on a huge compressed air network with 100000+ hose clams Ĺ” 1”. Every time there was a failure it...
  8. Replies
    13
    Views
    2,111

    Damn you got 0.69! I only got 0.61!

    Damn you got 0.69! I only got 0.61!
  9. Replies
    2
    Views
    201

    if the VR is aftermarket its highly suspect ...

    if the VR is aftermarket its highly suspect

    the alternator wiring can be soldered if the connector is burnt, as I'd lay even money it is since you've replaced the regulator and battery recently
    ...
  10. Replies
    55
    Views
    7,825

    Sounds like it's MOTEC time

    Sounds like it's MOTEC time
  11. Replies
    2
    Views
    270

    pull the valve cover, you should be able to tell...

    pull the valve cover, you should be able to tell if the valve is dropped or not.

    that kind of hit on a sparkplug indicates a dropped valve.

    Running past the redline tends to do that, and even...
  12. Replies
    6
    Views
    753

    Your right, When Im cruising with my "old" 2004...

    Your right, When Im cruising with my "old" 2004 RXP and new ski's with "brats" on it blow by way too close, I usually pull up beside them and wave bye as i pull away.
    Yep , someone is always...
  13. Thread: Got wooped!

    by troyheb
    Replies
    6
    Views
    753

    Spend all the money you want. There will always...

    Spend all the money you want. There will always be someone faster.
  14. Replies
    4
    Views
    411

    After replacing fuel pump have the ecu reflashed....

    After replacing fuel pump have the ecu reflashed. Tuning via the rrfpr is not optimal.
  15. Replies
    5
    Views
    403

    View Post

    Donít forget to upgrade the flywheel bolts if you ever decide to go above stock rpm limit with a tune.
    Above 8350 rpm upgraded springs and retainers are also recommended for the valve train.
  16. more like $3500-4500 unless it speaks mandarin,...

    more like $3500-4500 unless it speaks mandarin, $5k tops if it had a decent trailer.

    then again..covid had jacked prices up on just about anything that burns guzzeline so I might be out of line...
  17. Replies
    3
    Views
    426

    the R&D grate is actually the best grate for that...

    the R&D grate is actually the best grate for that ski.
  18. I've re-read your mod list 3 times just to be...

    I've re-read your mod list 3 times just to be sure I was not missing something. I don't see any power mods in that list so what made you think you would gain speed? The intercooler will help on...
  19. Replies
    10
    Views
    1,704

    Get yourself a workshop manual, very...

    Get yourself a workshop manual, very informative.474135474136474137
  20. Have the SC rebuilt in the Green Hulk store. It...

    Have the SC rebuilt in the Green Hulk store. It will be done with an OEM kit. The kit comes with bearings, shaft, seals, clutch & spring washers. The catch can is always a good idea in my book. The...
  21. Little update on it, have put 6 hrs on it re...

    Little update on it, have put 6 hrs on it re checked the tq on the head studs, this things is running great with plenty of power.
  22. Replies
    43
    Views
    5,186

    Viper Performance can supply them for $160 plus...

    Viper Performance can supply them for $160 plus shipping., PM me if you would like a set

    ...
  23. Replies
    24
    Views
    1,900

    Adding some more... There's a chicken or the...

    Adding some more...

    There's a chicken or the egg effect with supercharged jet skis. To make more power you need higher RPM, adding a higher pitch impeller reduces RPM but allows higher speed at...
  24. Replies
    43
    Views
    5,186

    I'd rather see SeaDoo adopt the same setup as...

    I'd rather see SeaDoo adopt the same setup as Yamaha, Kawasaki, or Honda.
  25. 2019 Seadoo GTX Limited 300 Stage 4 build

    Wanted to show the final product of my winter Build. Paid 6500 bucks for this insurance wreck. Somehow I ended up with a clear title on this ski. Total cost me around $20k. Here is a list of...
Results 1 to 25 of 359
Page 1 of 15 1 2 3 4