Search

Type: Posts; User: king

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    31
    Views
    1,183

    Ok, I will try to re-timing but, I need to use...

    Ok, I will try to re-timing but, I need to use TDC gauge because it is in the hull right? and after that I will upload the photo of it.

    Thank you Scottkrissinger
  2. Replies
    31
    Views
    1,183

    Yes, I count them it is 31 pins but the chain at...

    Yes, I count them it is 31 pins but the chain at exhaust cam always slack not go inside spoket and I don't no why

    thank you
  3. Replies
    31
    Views
    1,183

    Yes, the chain is slack always in exhaust cam...

    Yes, the chain is slack always in exhaust cam side I try to pull it then put the rest of chain on the intake cam but after I install the tensionor it jump again and become like the picture I don't...
  4. Replies
    31
    Views
    1,183

    I think yes, but can you see if it is right or...

    I think yes, but can you see if it is right or not ? and this is a photo of the timing I made before install the engine

    http://greenhulk.net/forums/attachment.php?attachmentid=457307&stc=1
    ...
  5. Replies
    31
    Views
    1,183

    Hello every Today I run it and it just want...

    Hello every

    Today I run it and it just want to turn off and I don't know why. The rpm rev up down for few seconds and then it shutoff and if I hold the throttle to keep it on 1000 rpm it vibrate....
  6. Replies
    31
    Views
    1,183

    Injectors seized like member say

    Hi,

    Today, I buy the new fuel pump from the dealer and I install it but the engine not work after that I check the spark plug not wet (no gas on it). So, I pull the injectors to local car workshop...
  7. Replies
    31
    Views
    1,183

    I check the fuel pump and it's not working and...

    I check the fuel pump and it's not working and the coil is short :(
  8. Replies
    31
    Views
    1,183

    Here how is my fuel pump screen and fuel tank...

    Here how is my fuel pump screen and fuel tank look like, Now I will check it with 12 v battery after clean it

    http://greenhulk.net/forums/attachment.php?attachmentid=457142&stc=1
    ...
  9. Replies
    31
    Views
    1,183

    I check today the coil all have spark. The...

    I check today the coil all have spark. The problem is fuel pump not prime gasoline to the injectors and now I try to remove the fuel pump to check it
  10. Replies
    31
    Views
    1,183

    Maybe like you say because they siting in the...

    Maybe like you say because they siting in the shelf for 1 year from 6 Jan 2019 until today I install everything and try to start it with ''bAt'' sign in the cluster.

    I will check tomorrow morning...
  11. Replies
    31
    Views
    1,183

    I clean the intercooler coil with small needle to...

    I clean the intercooler coil with small needle to smash the salt in between and it pass the leak test. Today,I install everything after full rebuild engine (new crankshaft,new connecting rod, new...
  12. Replies
    31
    Views
    1,183

    I will make an leak test to check if there any...

    I will make an leak test to check if there any leaks in the intercooler.
    But, If it pass the leak test is this mean it's in good condition and I don't need to change the intercooler anymore?
    ...
  13. Replies
    31
    Views
    1,183

    You mean these spray cans for cleaning the coil ...

    You mean these spray cans for cleaning the coil :

    http://greenhulk.net/forums/attachment.php?attachmentid=456894&stc=1

    http://greenhulk.net/forums/attachment.php?attachmentid=456895&stc=1
    ...
  14. Replies
    31
    Views
    1,183

    I don't know because I buy it as not working and...

    I don't know because I buy it as not working and owner ask me it sink before but he repaired it.

    thank you
  15. Replies
    31
    Views
    1,183

    Ultra 250x final step !!!

    Hi,

    I finish engine rebuild and now before install engine I remove the intercooler and this what is inside it :

    http://greenhulk.net/forums/attachment.php?attachmentid=456868&stc=1
    ...
  16. Replies
    2
    Views
    224

    Ok,I buy the both front bearings from the dealer...

    Ok,I buy the both front bearings from the dealer but, it's normal that the bearing move free not tight in the impeller shaft when I fit them ?
  17. Replies
    2
    Views
    224

    300X JET PUMP BEARINGSdimensions

    Hello everybody

    Can any one tell me the dimensions of ultra 300x bearing 92045-3744 - Front bearings x 2.

    because I work in upgrade my ultra 250x jet pump
  18. Replies
    4
    Views
    504

    Thanks for the advice blakegjones...

    Thanks for the advice blakegjones ,boudin


    I try to make timing for second time and I end up with:




    http://greenhulk.net/forums/attachment.php?attachmentid=455817&stc=1
  19. Replies
    4
    Views
    504

    Can anyone see my timing if it is correct or not...

    Can anyone see my timing if it is correct or not ?


    http://greenhulk.net/forums/attachment.php?attachmentid=455691&stc=1

    http://greenhulk.net/forums/attachment.php?attachmentid=455692&stc=1 ...
  20. Replies
    4
    Views
    504

    08 ultra 250x timing

    Hi

    I install the engine completely but how to make engine timing I read from my service manual but I confuse. Anyone can tell me how to do it by steps.


    Thank you
  21. Replies
    7
    Views
    347

    Thanks for everybody

    Thanks for everybody
  22. Replies
    7
    Views
    347

    Hello The job is done I try for last time...

    Hello

    The job is done I try for last time with using flat screw driver and my fingers and it come down in it place and now installing the cylinder head.


    thank you
  23. Replies
    7
    Views
    347

    Yes, I know that it go in from the bottom and...

    Yes, I know that it go in from the bottom and when I use the zip ties I put each one on the ring and when I put the cylinder the zip tie slide down and the rings open again.


    thank you
  24. Replies
    7
    Views
    347

    250X ULTRA cylinder install

    Hi,

    Anybody can tell me how he install the cylinder inside the piston ?
    I use tight cable and it not work I made tool from thin metal and also, It is not work I use my finger one piston get...
  25. Replies
    13
    Views
    458

    I think you should replace bolts with nuts if you...

    I think you should replace bolts with nuts if you tighten them because they are stretch when you tight them and in cars the same thing and there is a special tool to measure how much it stretch and...
Results 1 to 25 of 88
Page 1 of 4 1 2 3 4