Search

Type: Posts; User: K447

Page 1 of 8 1 2 3 4

Search: Search took 0.30 seconds.

  1. This is just for filtering the inter cooler water...

    This is just for filtering the inter cooler water feed flow?

    So after the X fitting in the cooling feed from the jet pump.

    Does it need to allow full water draining between rides or for winter...
  2. Thread: Exhaust hoses

    by K447
    Replies
    1
    Views
    51

    Welcome. What model year Genesis? 1999 has...

    Welcome.

    What model year Genesis? 1999 has different exhaust.

    Just need the exhaust hoses? The plastic resonators are still good?

    Which hose(s) do you need?

    You can find the parts...
  3. Replies
    2
    Views
    45

    Have you looked here...

    Have you looked here?
  4. Completely disconnecting the fuel float circuit...

    Completely disconnecting the fuel float circuit will cause the MFD to display no fuel level bars at all. I suspect it would not trigger a ‘Low Fuel’ RPM Limit under this condition.

    You can more...
  5. Replies
    5
    Views
    129

    My understanding (which may be incomplete) is...

    My understanding (which may be incomplete) is that all the 1.8 liter engines prior to 2016 used the same timing chain. After 2016 the timing chain was revised. Most, but not all, of the pre-2016...
  6. Replies
    1
    Views
    44

    That may be the wire guide, which fits inside the...

    That may be the wire guide, which fits inside the flywheel housing to keep the stator wire bundle away from the flywheel.
  7. Replies
    4
    Views
    71

    Gear puller or similar tool that can hook inside...

    Gear puller or similar tool that can hook inside the broken neck piece and yank/impact it rearwards?

    Or remove the flywheel cover, flywheel, Bendix and then drive the broken piece rearwards.
  8. Replies
    5
    Views
    129

    What kinds of water would you be riding in? ...

    What kinds of water would you be riding in?

    Passengers or solo?

    Yamaha redesigned the VXR for 2015, now it is much better in rough water, overall a more modern hull. And it includes the RiDE...
  9. Replies
    8
    Views
    239

    Can it be relocated higher in the hull without...

    Can it be relocated higher in the hull without modifying the wire harness?

    There are holes that allow seawater inside the ECU? :-?
  10. Replies
    5
    Views
    121

    View Post

    Don’t see how/why it would significantly affect fuel tank pressure.
  11. Replies
    6
    Views
    162

    Well, 15 per 1000 units is a 1.5% failure rate....

    Well, 15 per 1000 units is a 1.5% failure rate. Certainly not terrific, but even that rate means 98.5% did not have such failures.

    I have been buying and recommending Triton brand welded aluminum...
  12. Replies
    5
    Views
    121

    While it requires the fuel tank venting check...

    While it requires the fuel tank venting check valve to be in place and working, whether there is a noticeable difference between internal and outside air pressure also depends on the local weather. ...
  13. Thread: Look normal?

    by K447
    Replies
    14
    Views
    426

    I use a thin coating of bearing grease, on the...

    I use a thin coating of bearing grease, on the actual o-rings. Just enough to make the o-rings tacky and stay in place.

    The o-rings depend on the groove walls, and the top and bottom faces, to all...
  14. Replies
    6
    Views
    162

    Salt water or fresh water? How long do you...

    Salt water or fresh water?

    How long do you hope to keep the same trailer?

    How much towing distance do you expect to do?

    Are you OK with paying more for nicer things?
  15. When the LR-503 module is bypassed; it is not...

    When the LR-503 module is bypassed;
    it is not sensing anything.
    The red button cranks the starter. Even if engine is already running.
    And the lanyard pull is supposed to shut the engine off, by...
  16. Thread: Look normal?

    by K447
    Replies
    14
    Views
    426

    Start with a flat sheet of 400 grit (approx). See...

    Start with a flat sheet of 400 grit (approx). See how it looks after the initial rubbing. Look for high or low spots, indications of warp or out of flat.

    If the head is flat then you aren’t...
  17. The Black/Yellow wire with flat tab end is the...

    The Black/Yellow wire with flat tab end is the ignition kill signal. GROUNDING that wire to the black wire group should force the CDI (or EMM) to shut down ignition.


    Edit: The following is just...
  18. Welcome. The factory paint Yamaha uses is...

    Welcome.

    The factory paint Yamaha uses is beyond soft. Just rubbing the paint with a clean micro-fiber cloth can leave micro-scratches :-?

    Right behind the super thin soft paint layer is a much...
  19. Welcome. Did this machine ever run properly...

    Welcome.

    Did this machine ever run properly for you?

    Is the CDI new? If yes, sourced from where?

    Why would you jump from battery + to any yellow/black wire?

    If the engine would not crank...
  20. Replies
    4
    Views
    129

    Remove the intake grate, then use knife/tools to...

    Remove the intake grate, then use knife/tools to remove the flag material.

    You can probably evaluate whether any damage occurred while you are in there.

    Did the engine overheat at all? If...
  21. Thread: Look normal?

    by K447
    Replies
    14
    Views
    426

    Might also consider rigging up a leak down test...

    Might also consider rigging up a leak down test for the engine+exhaust manifold water jacket.

    Cap off the various hose fittings and so on. Then pressurize the water jacket with maybe 10 PSI, close...
  22. Thread: Look normal?

    by K447
    Replies
    14
    Views
    426

    At this point you need to work through every...

    At this point you need to work through every little thing, make sure it is all perfect. This amount of trouble getting the water jacket to seal properly is not normal.

    I would put each head on a...
  23. Replies
    8
    Views
    239

    Is there a known issue with the factory wire...

    Is there a known issue with the factory wire harness on EX models?
  24. Replies
    9
    Views
    151

    How often do you expect to be checking fuel...

    How often do you expect to be checking fuel pressure?

    Unscrewing the Schrader valve core before doing a fuel pump pressure test takes maybe 30 seconds.
  25. Replies
    2
    Views
    77

    There is a Seadoo part number that is a drop in...

    There is a Seadoo part number that is a drop in upgrade replacement solenoid.

    Click below, search in there for solenoid

    http://polarispwcknowledge.shorturl.com/first-things-to-do
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4