Search

Type: Posts; User: Kosh

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Sticky: Not going with the hand guards as well? im...

    Not going with the hand guards as well?

    im interested in finding out if they stay in position given the single bolt mount.
  2. Replies
    9
    Views
    247

    On the MSX,s it's on the underside of the top...

    On the MSX,s it's on the underside of the top deck, try a mirror if its uncomfortable.
  3. Replies
    77
    Views
    2,539

    You could just use all OEM seadoo and all you...

    You could just use all OEM seadoo and all you would need to do would be make an adaptor at your through hole for the bellows, you would need to run a doo pump or have your impeller modded to suit the...
  4. Sticky: I have had my GTX230 grate off, did not realise...

    I have had my GTX230 grate off, did not realise it had a nut on top of the threaded plate and spun the assembly breaking the small tab. I'll call it a plate as it is not an insert. It is a cast alloy...
  5. Replies
    77
    Views
    2,539

    Looking forward to reading about the journey, let...

    Looking forward to reading about the journey, let the fun begin.
  6. My 2019 GTX, Was off and needed a shim as well to...

    My 2019 GTX, Was off and needed a shim as well to get it close, to get it perfect it still needs the through hull redoing. Dissapointing.
    if I did not like the ST3 hull so much for the conditions I...
  7. Replies
    3
    Views
    295

    FS - Parts Bugger!

    Bugger!
  8. Yes there is. 12 hydraulic valve lash adjusters.

    Yes there is.
    12 hydraulic valve lash adjusters.
  9. Yes just cover the hole, poke that fly wheel...

    Yes just cover the hole, poke that fly wheel while you are there, as suggested it may be loose.
  10. There is no filter bypass on these engines,...

    There is no filter bypass on these engines, contrary to the very nice video that shows the oil flow in a 4tec
  11. Replies
    5
    Views
    263

    I could not find a non vented cap for my 12 RXPX...

    I could not find a non vented cap for my 12 RXPX so had one made , it is the same cap that now fits my GTX230.
    If you do make your own just ensure the material you use will will not react with fuel....
  12. Thread: Fuel problem

    by Kosh
    Replies
    5
    Views
    272

    As above, you need to turn off auto tune below...

    As above, you need to turn off auto tune below 2000rpm and do that area manually.
  13. .

    .
  14. To make it worse the recall notice has mistakes...

    To make it worse the recall notice has mistakes as well! References to the cooler latch!
  15. Thia should help

    Thia should help
  16. Thread: Water pump seals

    by Kosh
    Replies
    5
    Views
    343

    Pressure test the oil cooler out before you go...

    Pressure test the oil cooler out before you go pulling the pump apart.
  17. Replies
    203
    Views
    39,654

    Very nice job, looking forward to the first ride...

    Very nice job, looking forward to the first ride report.
  18. Replies
    5
    Views
    502

    Is there not a throttle body offset change on the...

    Is there not a throttle body offset change on the latter models? They repositioned the oil filter housing on the PTO.
    Im not sure when but I think it was with the change to the Bosch ECU management?
  19. Replies
    571
    Views
    53,253

    Been a few years since the last post on the...

    Been a few years since the last post on the MSX215+ , still as much fun as the day it went together and still going strong.:D
  20. They are still getting it wrong in 2019 (gtx230)...

    They are still getting it wrong in 2019 (gtx230) through hull was out as well as engine.
    2018 gtx155 I just checked was ok.
    One day they will all be perfect from the factory!
  21. Replies
    6
    Views
    244

    First thing would be to check for a collapsed oil...

    First thing would be to check for a collapsed oil filter.
    Do the Easy stuff first.
  22. Replies
    13
    Views
    4,730

    I would imagine the sponsons would be different...

    I would imagine the sponsons would be different to the GTX, they are on the RXT300 and are not interchangeable. Less aggressive in turns for the GTX.
  23. Replies
    5
    Views
    365

    GTX155 and you wil not be dissapointed, the IS...

    GTX155 and you wil not be dissapointed, the IS was dropped for a good reason.
  24. Replies
    6
    Views
    303

    The water box has rubber hoses clamped to it so I...

    The water box has rubber hoses clamped to it so I would not get to worried a hose resting against it.
  25. Good to see you keeping the dream aliveO:)

    Good to see you keeping the dream aliveO:)
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4