Search

Type: Posts; User: Team Bilford

Page 1 of 8 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    20
    Views
    746

    Glad you found the issue, hopefully not too much...

    Glad you found the issue, hopefully not too much pain to replace the hose. Any idea why the hose failed?
  2. Tim did a great job of explaining the features of...

    Tim did a great job of explaining the features of the RXT-X. I did notice however, he did not discuss construction materials like CM Tec as being better than the competition. Two years ago, that's...
  3. Replies
    4
    Views
    543

    Those EZ Lube type of hubs are a great way to...

    Those EZ Lube type of hubs are a great way to ruin your bearings. Yes, it makes it easier to push the water out with the addition of new grease, but it makes much more sense to not let the water get...
  4. Replies
    3
    Views
    213

    Any of the issues with the 18 and 19 will most...

    Any of the issues with the 18 and 19 will most likely be present in the 20. I don't follow the RXT issues as closely as the RXP, but I don't think that there have been any changes.
  5. Replies
    2
    Views
    261

    JASO MA certified

    JASO MA certified
  6. That is a 97 model with a 787/785 engine 110 hp.

    That is a 97 model with a 787/785 engine 110 hp.
  7. OK, I'll bite..... If you run the oil level mid...

    OK, I'll bite.....
    If you run the oil level mid kink or lower on a stock ski, you might not have a need. I did not have any oil in my can for a long time, but after I added a simple SCOM, the...
  8. Replies
    17
    Views
    1,496

    Do you have a pic of it mounted?

    Do you have a pic of it mounted?
  9. Replies
    3
    Views
    389

    I think the best ski is the one nobody rides...

    I think the best ski is the one nobody rides anymore...… I love the XPL.
    There are a few people on the forum that have both skis that you are looking for. Try the search feature and see if you can...
  10. Replies
    1
    Views
    328

    I read on another thread that that feature was...

    I read on another thread that that feature was dropped with the new display in 2019, but you get turn signals!
    I look at my engine temp on my 18 RXP frequently, I would really miss that info.
  11. Replies
    25
    Views
    1,571

    Were the cracks in the hull or the top deck?

    Were the cracks in the hull or the top deck?
  12. Replies
    12
    Views
    1,164

    The can does vent into the engine compartment. ...

    The can does vent into the engine compartment. There has to be air flow to the can. My personal experience is that the smell is not strong enough to bother me and quickly clears when the seat is...
  13. Replies
    12
    Views
    1,164

    I put a 90 degree ball valve on my GRF rather...

    I put a 90 degree ball valve on my GRF rather than the screw in valve.
  14. Jerry, You mentioned using the holding tool...

    Jerry,
    You mentioned using the holding tool while testing the slip. Do you normally pull the SC to make the 200 hour slip test? The shop manual mentions an on engine procedure as well. Is one...
  15. Replies
    10
    Views
    964

    I use a similar technique with my engines. Two...

    I use a similar technique with my engines. Two or three times during the off season, I spin my engines over to spread oil, but do not start them. I think that is better protection than simply using...
  16. Replies
    10
    Views
    964

    That's very good info to have. I store my 300 in...

    That's very good info to have. I store my 300 in a heated shop and only do the air method one time. I would hate to think that damage would occur if stored in freezing temps since the shop manual...
  17. Replies
    10
    Views
    964

    I blow my 300 out right after flushing. I rev the...

    I blow my 300 out right after flushing. I rev the engine and blow out most of the water before I hook up the air hose. I have never measured the amount of water, but I would guess that it is about 2...
  18. Replies
    5
    Views
    250

    While using compressed air or antifreeze will...

    While using compressed air or antifreeze will protect the water pathways in the IC, neither will remove any condensation sitting in the IC body. It is possible, but unlikely that if the condensation...
  19. Replies
    9
    Views
    751

    If your ski is exposed to freezing temps, you...

    If your ski is exposed to freezing temps, you should use one of the antifreeze techniques mentioned. My RXP 300 is stored in a heated shop so all I do is the compressed air at 55 psi to blow out the...
  20. Replies
    14
    Views
    1,023

    The fuel burn of a XPDI is so efficient. I was...

    The fuel burn of a XPDI is so efficient. I was shocked to death by the burn of the 300. The XP or RX DI has the best range of all the skis.
  21. Replies
    14
    Views
    1,023

    I love the XPL and waited 10 years before selling...

    I love the XPL and waited 10 years before selling one of mine for a RXP 300. While you might think that they would sell, the stats don't support you. Most buyers wanted something bigger and the...
  22. Replies
    14
    Views
    1,023

    How about a nice lightweight 130 HP 2...

    How about a nice lightweight 130 HP 2 stroke.....wait, you had one of those! I still doo
  23. Replies
    9
    Views
    1,153

    I headed to LBJ and Canyon this weekend for a...

    I headed to LBJ and Canyon this weekend for a last ride of the season. If anybody else is headed out, let me know.
  24. I have responded to your PM.

    I have responded to your PM.
  25. Replies
    8
    Views
    940

    No coolant in the cylinders. I pulled the plugs...

    No coolant in the cylinders. I pulled the plugs and spun it over, no moisture and the plugs look good.
    Its getting late in the season and I would like to find the problem. I'll ride again this...
Results 1 to 25 of 200
Page 1 of 8 1 2 3 4